Alpine CDA-118M - Manual (Page 50)

48
-EN
Front Output/Input RCA Connectors
It can be used as Front Output or Input RCA Connectors.
Rear Output/Input RCA Connectors
It can be used as Rear Output or Input RCA Connectors.
ZONE2 Output RCA Connectors
Subwoofer Output RCA Connectors
USB Connector
Connect this to an USB memory or to an iPhone/iPod. To
use an iPhone/iPod, Interface cable for iPod connection is
required.
• Use the supplied USB cable. If a USB cable other than the supplied is
used, correct performance cannot be guaranteed.
• Route the USB cable away from other cables.
Marine Remote Commander Connector
This connector is used to connect the Marine Remote
Commander (sold separately).
For details about connections, consult your nearest Alpine
dealer.
Ai-NET Connector
Connect this to the output or input connector of another
device (CD Changer, Equalizer, HD Radio TUNER
MODULE, etc.) equipped with Ai-NET.
• Be sure to set “Setting the Connected Head Unit (MODEL SETUP)”
to “CD CHG”, when the DHA-S690 is connected.
• Interface adapter for iPod (KCA-420i) is not recommended for use
with this product.
• You can input TV/video sound by connecting an optional
Ai-NET/RCA Interface cable (KCA-121B) to this component.
Ai-NET Cable (Included with CD Changer)
Antenna Receptacle
AUX Input Terminal
This terminal allows for input of audio from an external
device (such as a portable player), using a commercially
available converter cable. Refer to “Setting the AUX ZONE
Mode” (page 24).
Steering Remote Control Interface Connector
To Marine Remote Commander (sold separately).
For details about connections, consult your nearest Alpine
dealer.
BLUETOOTH interface connector
Connect this to an optional BLUETOOTH INTERFACE
(KCE-400BT). To use a hands-free mobile phone, an
optional BLUETOOTH INTERFACE (KCE-400BT)
connection is required. For details on connection, refer to
the Owner’s Manual of the BLUETOOTH INTERFACE
(KCE-400BT).
You can also connect this to an external device (such as a
portable player) by using Conversion cable (KCE-237B) for
building up the AUX IN (sold separately).
• Refer to “Setting the AUX+ Mode” (page 24).
Power Supply Connector
System Switch
When connecting a processor or divider using Ai-NET,
place this switch in the EXT AP position. When no device is
connected, leave the switch in the NORM position.
When switched to NORM, the RCA Connectors
and
can be used as Output RCA Connectors.
When switched to EXT AP, the RCA Connectors
and
can be used as Input RCA Connectors.
• Be sure to turn the power off to the unit before changing the switch
position.
KCE-400BT Connection Cable (Included with
KCE-400BT)
Remote Turn-On Lead (Blue/White)
Connect this lead to the remote turn-on lead of your
amplifier or signal processor.
Power Antenna Lead (Blue)
Connect this lead to the +B terminal of your power antenna,
if applicable.
• This lead should be used only for controlling the boat’s power
antenna. Do not use this lead to turn on an amplifier, or a signal
processor, etc.
Audio Interrupt In Lead (Pink/Black)
Switched Power Lead (Ignition) (Red)
Connect this lead to an open terminal on the boat’s fuse box
or another unused power source which provides (+)12V
only when the ignition is turned on or in the accessory
position.
Battery Lead (Yellow)
Connect this lead to the positive (+) post of the boat’s
battery.
Fuse Holder (10A)
Ground Lead (Black)
Connect this lead to a wire connected directly to the boat’s
negative battery terminal.
Right Front (+) Speaker Output Lead (Gray)
Right Front (–) Speaker Output Lead (Gray/Black)
Right Rear (–) Speaker Output Lead (Violet/Black)
Right Rear (+) Speaker Output Lead (Violet)
Left Rear (+) Speaker Output Lead (Green)
Left Rear (–) Speaker Output Lead (Green/Black)
Left Front (–) Speaker Output Lead (White/Black)
Left Front (+) Speaker Output Lead (White)
AUX+ ON : When the external device is connected.
AUX+ OFF : When set to OFF, AUX+ source cannot be
selected.