Reese 56007 OUTBOARD CUSTOM QUICK INSTALL KIT - Manual (Page 6)

© 2013 Cequent Performance Products 56007N 4-17-13 Rev. B
 Do not install mounting rails over plastic bed liners. Plastic bed liners must be cut out of the way to provide
metal to metal contact. Mounting rails may be installed on spray in liners.
 Use only bolts, nuts, and washers supplied to install this kit. All bolts and nuts are Grade 8 unless otherwise
specified.
 These instructions are guidelines only, actual installation is the responsibility of the installer and the owner.
Always measure truck and trailer before installing hitch to be sure that there is clearance at the cab and at the
bumper to allow for turns.
 Do not install this product on or attempt to tow with a truck with a 5- 1/2’ bed unless a sidewinder pinbox coupler
has been installed on the trailer.
Warning!!
When installing to Figure 5 & 6, during drilling protect the fuel tank and filler tubes, brake lines and wire harness by placing a piece of
metal between the box floor and potential components at risk on the driver’s side. This will prevent drilling into these items.
Installation Instructions
1. Lower and remove spare tire. Remove exhaust heat shield from the underneath the passenger side of the vehicle.
2. Place one mounting rail in the bed of the vehicle. Center the rail on the floor of the truck bed and use your tape measure to locate the
proper distance from the rail to the to the rear edge of the truck box as illustrated on page 7.
3. Use a center punch to mark the holes in the rail per the illustration. Move the rail out of the way and drill each position with a 1/8” drill
bit. Note: When drilling holes through the bed be sure what is below the truck bed in those locations.
4. Temporarily position the frame brackets on the sides of the frame and check that the 1/8” drilled holes align with the slots in the frame
brackets. Remove the frame brackets from the vehicle.
5. Enlarge the 1/8” drilled holes to 9/16”.
6. Fasten the frame brackets to the vehicle frame rails as shown in Figure 5. Using the pull wire (11) thread the button head cap screw (6)
and the conical washer (4) through the rearward slot, on the interior of the truck frame. Place the mounting bracket (1), conical washer
(4), and the 5/8” nut(3) on and hand tighten.
7. Passing the 1/2” carriage bolts (9) through the top and middle slots in the reinforcement block (10) will create a clamping strap that will
go inside the frame rail and connect to the mounting bracket (1). There are two different holes in the mounting bracket that allow for
the best clamping surface to the truck frame. Changing the mounting bracket hole will allow the clamping strap to adjust to different
height truck frames. Once the strap bolt have been passed through the best mounting hole thread the reinforcement block (10), 1/2”
conical washer (8), and the 1/2” nut (7) on to the bolts and hand tighten.
8. On some model years of trucks there could be a large gap between the truck frame and the inside face of the mounting bracket. If that is
true for your truck, remove the nuts and washers from the previous step, remove the reinforcement block from the outside of the bracket
and thread it on the strap bolts on the inside of the mounting bracket. Pass 1/2” bolts through the correct hole, thread washers and nuts
back into place and re-hand tighten.
9. Reposition the mounting rail over the holes in the bed and fasten the mounting rail to the frame brackets using the hardware supplied
with the rail kit. Use the U-shaped blocks between the frame bracket or mounting rails and the truck bed to ensure metal to metal
contact. Install center bolt and hand tighten.
10. Place the unassembled 5 th wheel support arches/slider/goose into the already installed mounting rail. Position the rearward mounting
rail with the support arches/slider/goose by inserting the tabs into the mounting rail and pushing the mounting rail tight towards the other
mounting rail. Ensure that the mounting rail is centered on the bed of the vehicle. This will position the rail in the correct location and
ensure that the 5
th wheel will have a snug fit to the truck. Note: If more than one hitch product will be used with the mounting rails then
both types should be used at the same time to align the rearward mounting rail. This will ensure that one product does not compromise
the fit of the other.
11. Repeat installation steps 4, 6 and 9.
12.
Starting with the hardware that fasten the mounting brackets to the frame torque all the nuts. Torque the 1/2” fasteners to 110ft-lbS
(149N*M), and the 5/8” bolts to 212 ft-lbs (287N*M).
13. Re-install spare tire.
Sheet 6 of 7