LED LENSER X21R.2 - Manual (Page 5)

Pressing the button once more will turn the lamp off.
7.4 Light Program Signal ( )
In the fourth position from the left, by switching or tapping, the Light
Function SOS (3 short, followed by 3 long, followed again by 3 short
flashes) can be invoked immediately.
When the Light Function SOS is activated, tapping the switch will cycle
through two additional functions. The first tap will activate the Light
Function Blink (slow, continuous blinking). Tapping once again will
activate the Light Function Signal Blink (double flash at short intervals).
Tapping a third time will activate the Light Function SOS again.
Pressing the button one more time will turn the lamp off.
7.5 Light Program Defence ( )
The Light Mode Defence is the one on the extreme right on the selection
ring; it can be selected by turning the selection ring completely to the left
till it comes to a stop.
After operating the switch the Light Function Strobe is set. Afterwards,
by tapping briefly it is possible to toggle between the Strobe and the
Power Mode.
Pressing the button once more when the lamp is on will turn the lamp
off.
Like in the other Light Modes 2 to 4, the Light Functions can be cycled
through by successively tapping the switch; this means, for example, that
in Light Mode 5, tapping the switch when in the Light Function Power will
enable the Light Function Defence and vice versa.
When the X21R.2 is operating in one of the Light Functions (2, 3, 4 or
5), turning the “Fast Action Switch“ will immediately switch over to the
corresponding Light Function. After such a changeover, the X21R.2 will
have the same Light Function enabled that it would have when first
turning the “Fast Action Switch“ and then switching on the lamp, e.g. with
the Light Program Signal, the Light Function SOS would be activated.
8. Emergency Mode / Emergency Light Function
When the Emergency Mode is activated, the X21R.2 has an emergency
light function. To use this function, the mode has to be activated and the
X21R.2 has to be connected to the charger (position light at the charger
glows blue, see Point 10). In this case, the torch automatically goes on
when the electric supply that is providing energy to the charger fails.
If positioned meaningfully, the X21R.2 can facilitate finding quickly an
escape route in an emergency, or the lamp can be quickly found and
picked up, already switched on. If this function is active, the X21R.2
shines automatically even if the charging process is interrupted by
removing the X21R.2. Therefore, the function can also be used when the
X21R.2 has to be ready for immediate use.
To set the Emergency Mode, set the „Fast Action Switch“ to ( the second
position) Light Program Low and tap prolonged for about 10 seconds.
The X21R.2 glows for these 10 seconds and then blinks. After blinking,
the light turns off. When it flashes 4 times, Emergency Mode is activated;
if it flashes twice, Emergency Mode is disabled. If this procedure is
carried out again, the setting toggles between activated and disabled and
signals this by a corresponding blinking.
9. Reset function
Unscrewing the Power Module (shaft with “Safety Ytrion Cell“ battery
pack) from the lamp head and reassembling the two parts again after a
while will reset the X21R.2. This resets the following functions:
The Energy Mode, Energy Saving is active (see Point 6).
The Emergency Mode (see Point 8) is active.
The lamp function Dim (see Point 7.2) is set to the lowest brightness.
10. Charging
The Power Module (shaft without lamp head) contains the “Safety Ytrion
Cell“ battery pack, the rechargeable batteries.
Charge your X21R.2 only in a dry place.
For charging, connect the main cable on one side to the charger provided
(Input: 100 V to 240 V / 50 Hz to 60 Hz) and one the other side to a mains
power socket. Then connect the extension cable of the charger to the
cable of the magnetic charging socket, whose blue position light will start
to glow. You can now connect the concentric charging contacts at the end
of the X21R.2 to the magnetic charging socket. When the lamp has been
correctly attached, the charging display glows red (see Point 11) and the
charging starts. The Power Module (shaft with the “Safety Ytrion Cell“
battery pack) with the unscrewed lamp head can also be charged by
itself.
See the following section on the subject of the charging indicators (see
Point 11) for more information.
Note – Please ensure that there is no short-circuit at the charging
contacts. The charging contacts must not be touched with moist or
metallic objects.
The magnetic charging socket can also be inserted in the cylindrical part
of the charger bracket, which is part of the supplied kit, and then locked
into place by turning a couple of times in the counter-clockwise direction
like a bayonet lock. The lock is released by rotating in the other direction.
The bracket can be fastened on the wall with dowels (not supplied with
the lamp) in such a way that the blue position lamp of the magnetic
charging socket, for example, glows downwards. Please use a sufficient
number (min. 4 pieces) of suitable dowels, depending on the material of
the wall.
The orientation described suggests itself that when you wish to use the
Emergency Module / Emergency Light function (see point 8) the X21R.2
will shine upwards in case of a power failure. On the other side of the
bracket, the X21R.2 can be joined to the bracket with 2 rubber rollers
and fixed permanently by using the rubber gusset that is located at the
level of the two rubber rollers. The latter suggests itself if there are
acceleration forces acting on the X21R.2. In this manner, the X21R.2 can
be fixed in the bracket inside the vehicle if the charger bracket is fixed
permanently to a vehicle.
Using an optionally available car charger (needs to be purchased
separately), the X21R.2 can also be charged at the cigarette lighter and
power sockets in the vehicle. These accessory units adjust themselves
automatically to the respective input voltage (from nominal 12 V to 24 V).
When the car is off, the charger doesn’t provide output if the voltage of
the battery in the car is lower than 13.0V, in order to protect your car;
you cannot charge the torch in this condition.
11. Charge indicator
Approx. 2 cm before the end of the shaft of the X21R.2 is a narrow ring
which, during the charging process, indicates the charge status of the
battery through lamps of different colours.
Red: (glowing continuously) charging on going.
Green: (glowing continuously) charging completed, the X21R.2 is ready
for use with the full capacity of the battery. It generally takes 2 to 3 hours
for an empty X21R.2 to get fully charged.
No light: The cause of this can be that the Floating Charge System Pro is
not getting adequate electrical power. But it can also be that there is a
loose contact. Therefore, check whether (magnetic) objects or dirt are
preventing a good contact between the charging contacts at the end
of the X21R.2 and the magnetic charging socket. If required, remove
them. If required, also correct the position or the angle of the X21R.2
in the charging socket. If, given an adequate electric power supply, the
charge indicators still do not glow, immediately unplug the transformer
or the optional car charger of the X21R.2 from the present power supply
system and get in touch with your dealer.
12. 360° Power Indicator
The 360° Power Indicator consists of 10 blue-glowing elements, which
are arranged in a circle around the two concentric charging contacts at
the end of the shaft of the X21R.2.
During use the number of blue-glowing elements reduces further and
just before the Power Module is empty, the last element will glow in red.
Depending on when the charging contacts are pressed, the following can
be determined from the number of elements glowing.
12.1 Battery status indication
If the charging contacts are pressed while the X21R.2 is off, the elements
serve as a battery status indication. If, for example, all the 10 elements
briefly glow blue, the X21R.2 is fully charged.
12.2 Operating time indication
If the charging contacts of the X21R.2 are pressed while the X21R.2 is
being operated with a Light Function, the number of glowing elements
provides an indication of the remaining relative lighting duration of the
current Light Function.
The X21R.2 also shows this information for a brief moment when a Light
Function has been selected by tapping or switching at the “Fast Action
Switch“, i.e. even without the 360° Power Indicator having been actuated.
13. Changing the Power Module
Please charge the rechargeable battery in time. If the Power Module
exhibits any atypical behaviour, please change it. For changing the
rechargeable battery, please first switch off the torch and unscrew the
part behind the “Fast Action Switch“. You have thus separated the lamp
head from the Power Module (shaft including “Safety Ytrion Cell“ battery
pack). For the disposal of the used Power Module, please read Point 14.
Screw on a new Power Module onto the lamp head till it cannot be turned
any further. Thanks to the innovative new contact system and the fixed
connection between the lamp shaft and the “Safety Ytrion Cell“ battery
pack (Power Module), reversing the polarity is not possible.
14. Rechargeable batteries
Only the correspondingly approved LED LENSER Power Module
consisting of the “Safety Ytrion Cell“ battery pack and shaft may be used
in this pocket torch. The Power Module was developed to ensure the
highest level of safety and convenience.
If you have separated the used Power Module from the lamp head as
described in Point 13, please unscrew the rear part of the shaft at the
level of the charging display. When inspecting the tube, a PCB on the
end of the “Safety Ytrion Cell“ battery pack should be there. The PCB
is held in place on this side in the shaft by a narrow plastic ring with
thread. When removing the “Safety Ytrion Cell“ battery pack from the
shaft, unscrew this plastic ring from the shaft. For doing so, use the two
grooves in the plastic ring that are displaced 180° from one another, but
make sure that you do not short-circuit the contacts of the „Safety Ytrion
Cell“ battery pack. The „Safety Ytrion Cell“ battery pack can now be easily
removed and disposed of by observing the national laws. The shaft can
04
English | Page 03-05
GB