System Sensor SPS and SPSV series Wall and Ceiling speaker_strobes User Manual
Page 3
6.
Secure product by tightening the single mounting screw in the front
of the product housing. For tamper resistance, the standard captivated
mounting screw may be replaced with the enclosed Torx screw.
K Series Mounting
1. K Series products may be used indoors or outdoors. They must be in-
stalled using the proper SpectrAlert Advance weatherproof back box. Do
not attempt to use boxes other than those specified for use with the
product.
2. The plastic weatherproof back box is equipped with removable side
flanges for mounting. The back box may be secured directly to the wall
or ceiling using the flanges (plastic and metal back boxes) or by using
the knockout plugs(plastic back boxes). Knockout plugs are provided to
mount directly to the wall or ceiling or to a 1900 weatherproof electrical
box, see Figure 12.
3. Threaded holes are provided in the sides of the box for
3
/
4
inch conduit
adapters. Knockout plugs in the back of the box can be used for
1
/
2
or
3
/
4
inch rear entry. Unused holes must be sealed. Plugs and O-Rings are
provided with the box for this purpose.
4. It is the responsibility of the installer to make sure that all openings and
connections are sealed properly. Outdoor installations that are protected
from direct exposure to rain are still subject to condensation or leakage
through hidden areas, such as a soffit.
5. Water may pool on the back box due to condensation or direct exposure
to rain or snow. Use watertight fittings for all wiring connections, includ-
ing the knockout plugs on the back of the box. When using the plastic
plugs to fill unused threaded holes, make sure the O-rings supplied are
properly positioned on the plug. The plugs must be sealed with PTFE
thread seal tape.
6. Attach the mounting plate to the weatherproof back box using the four
non-painted screws.
7. Follow steps 2-5 of the indoor mounting instructions to wire and attach
the product. The product must be mounted to the weather proof back
box using the painted screws (wall product has 4 screws, ceiling product
has 3 screws)
CAUTION
The ‘hold-in-place’ snaps are not intended to secure the product to the back
box. The product must be secured to the back box using the screws provided
figure 9. WaLL mounT WeaTherproof produCT WiTh
pLasTiC baCk box:
A0395-00
mounTing
Mounting Indoor Wall or Ceiling Products
1. Attach mounting plate to junction box as shown in Figures 4 and 5. The
mounting plate is compatible 4˝ x 4˝ x 2
1
/
8
˝ junction boxes. If using a back
box skirt or trim ring, attach the mounting plate to the skirt or trim ring and
then attach the entire assembly to the junction box (see Figures 4, 6 and 8).
2. Connect field wiring to terminals, as shown in Figure 1.
3. If the product is not to be installed at this point, use the paint cover to
prevent contamination of the mounting plate.
4. To attach product to mounting plate, remove the paint cover, then hook
tabs on the product housing into the grooves on mounting plate.
5. Then, swing product into position to engage the pins on the product with
the terminals on the mounting plate. Make sure that the tabs on the back
of the product housing fully engage with the mounting plate.
SS-140-001
3 I56-3109-011R
figure 4: WaLL mounT produCT WiTh Trim ring:
A0389-00
figure 5: CeiLing mounT produCT:
A0390-00
figure 6: WaLL mounT produCT WiTh baCk box skirT:
A0392-00
figure 7. ouTdoor CeiLing mounT produCT WiTh pLasTiC
WeaTherproof baCk box:
A0420-00
figure 8: CeiLing mounT produCT WiTh baCk box skirT:
A0393-00