STI 6406 - Manual (Page 5)

- 4 -
Circuit Board Set-up
Figure 1
TERMINAL BLOCK
(SEE BELOW)
FOR COMPLETE ALARM OPTIONS
AND SWITCH SETTINGS SEE CHART
ON REVERSE SIDE.
PC BOARD
JP5
JP2
JP4
JP3
JP7
SWITCH
ALARM
DURATION
ALARM VOLUME SWITCH
TRIP DELAY SWITCH
ARMING SWITCH
) (
FACTORY DEFAULT SETTINGS
(FACTORY DEFAULT SETTINGS)
(ON)
(ON)
(OFF)
(OFF)
(OFF)
TERMINAL BLOCK
FOR COMPLETE ALARM OPTIONS
AND SWITCH SETTINGS SEE CHART
ON REVERSE SIDE.
PC BOARD
JP5
JP2
JP4
JP3
JP7
SWITCH
ALARM
DURATION
ALARM VOLUME SWITCH
TRIP DELAY SWITCH
ARMING SWITCH
) (
FACTORY DEFAULT SETTINGS
(FACTORY DEFAULT SETTINGS)
(ON)
(ON)
(OFF)
(OFF)
(OFF)
Switch Settings
Volume - High (105 dB) at 1 ft. ON*
Volume - Low (95 dB) at 1 ft. OFF
Duration - 30 Second Alarm OFF* OFF*
Duration - 180 Second Alarm OFF ON
Duration - Continuous Alarm ON OFF
Duration - Annunciator Mode ON ON
Trip - Immediate OFF*
Trip - 15 Second Delay ON
Arming - Immediate ON*
Arming - 15 Second Delay OFF
FEATURE JP2 JP3 JP4 JP5 JP7
*Factory Settings
Note: Slide black lever to desired ON/OFF position as labeled on circuit board.
POLYCARBONATE COVER
POLYCARBONATE BASE
120 dB HORN
ALARM DURATION
ALARM TRIP DELAY
EXIT DELAY
VOLUME
VIEW OF THE CIRCUIT BOARD
19039 SCREW
6 x 1 1/4 in.
(2) PROVIDED
19018 ANCHOR
(2) PROVIDED
BOTTOM SURFACE AS SHOWN
WIRES THROUGH NOTCH ON
AND ROUTE REED SWITCH
REMOVE FRONT COVER
VIEW SHOWING MAGNET INSTALLATION
MAGNET
NC COM NO GD V+ RS1 RS2 KEYSW
TERMINAL BLOCK WIRING CONNECTIONS
FORM
C
DRY CON
TACTS
RE
MOT
E
POWE
R
INPU
T
9-24
VD
C
R
EE
D
SW
ITCH
TE
R
M
IN
ALS
KE
Y
SW
ITCH
TE
RM
IN
ALS
INTERNAL REED SWITCH
(RS1)
ALARM DURATION
ALARM TRIP DELAY
EXIT DELAY
VOLUME
VIEW OF THE CIRCUIT BOARD
MAXIMUM GAP 3/4 in. (19mm)
3/8 in. (9.5mm) ON METAL DOOR
AND FRAME
SPACERS (USE AS NECESSARY)
NOTE: 2 SPACERS UNDER BOTH
MAGNET AND REED SWITCH
MUST BE USED ON STEEL DOORS
4
3
2
1
NC COM NO GD V+ RS1 RS2 KEY SW
SLOTS
FLANGES
TERMINAL STRIP
9 VOLT BATTERY
19011 TAMPERPROOF SCREW
(1) PROVIDED
19016 TAMPER WRENCH
(1) PROVIDED
BASE
19014 MOUNTING SCREW
(4) PROVIDED
REED SWITCH
MOUNTING LOCATIONS
(LABELED 1-4)
COVER
NC COM NO GD V+ RS1 RS2 KEY SW
4
3
2
1
NC COM NO GD V+ RS1 RS2 KEY SW
SLOTS
FLANGES
TERMINAL STRIP
9 VOLT BATTERY
19011 TAMPERPROOF SCREW
(1) PROVIDED
19016 TAMPER WRENCH
(1) PROVIDED
BASE
19014 MOUNTING SCREW
(4) PROVIDED
REED SWITCH
MOUNTING LOCATIONS
(LABELED 1-4)
COVER
4
3
2
1
ALARM SOUNDS WHEN DOOR IS OPENED
EMERGENCY USE ONLY
ON OFF
NC COM NO GD V+ RS1 RS2 KEY SW
SLOTS
FLANGES
TERMINAL STRIP
9 VOLT BATTERY
19011 TAMPERPROOF SCREW
(1) PROVIDED
19016 TAMPER WRENCH
(1) PROVIDED
BASE
19014 MOUNTING SCREW
(4) PROVIDED
REED SWITCH
MOUNTING LOCATIONS
(LABELED 1-4)
COVER
TO KEY
SWITCH
06402 REED SWITCH
(RS2)
OPTIONAL:
TO REMOTE
HORN
STI-6403
TERMINAL BLOCK
VIEW SHOWING INSTALLATION OF
ADDTIONAL REED SWITCH 06402
3/4 in. (19mm)
MAXIMUM GAP
3/8 in. (9.5mm) ON
METAL DOOR AND FRAME MAGNET ASSEMBLY
(SEE ABOVE FOR INSTALLATION)
DOOR
SWING
6400 SWING
MAGNET
DOOR STOP
MAGNET MUST BE
INSTALLED OPPOSITE
RAISED RIB ON OUTER COVER 19039 SCREW
6 x 1 1/4 in.
(2) PROVIDED
SPACERS - USE
AS NECESSARY NOTE: (2) SPACERS MUST BE
USED ON STEEL DOORS
19018 ANCHOR
(2) PROVIDED
MAGNET
6400 UNIT
DOOR
SWING
JAM
DOOR STOP
DOOR
TYPICAL FLUSH MOUNT DOOR JAM
INSTALLATION
TYPICAL RECESSED MOUNT DOOR JAM
INSTALLATION