STI 6406 - Manual (Page 6)

- 5 -
Alarm Feature Description
· Volume Switch JP2 - Sets alarm volume to high 105 dB or low 95 dB.
· Duration Switch JP3 and JP4 - Amount of time alarm sounds after trip. Arming resets at
end of duration if door is closed. Alarm will not reset if in continuous mode; alarm sounds
until battery is drained. Annunciator Mode is a series of 10 short beeps or until door is
closed.
· Trip Delay Switch JP5 - If you wish to ENTER an alarmed door without sounding the horn
immediately, the trip delay will allow 15 seconds for you to enter and de-activate the alarm
with the key switch before the alarm will sound.
· Arming Switch JP7 - This mode is useful when an AUTHORIZED EXIT is required through
alarmed door. In “ON” position immediate arming will set the alarm ready to function as
soon as door is opened. In “OFF” position delay arming will allow 15 seconds for you to exit
through the door without sending alarm signal.
Installation Instructions
1. Make sure key switch is in the OFF
position.
2. Remove tamper screw on side of unit
and remove housing cover. Save this
tool for future servicing and battery
change (Fig. 2).
3. Set switches, on circuit board, to
desired alarm settings (Fig. 1).
4. Test settings by connecting battery
or external power source. If using
external power source a Class II UL
Listed transformer is required. If power
is present at terminal block (Fig. 1) 9V battery
is in no-load on standby power consumption.
5. Mount main unit on or next to door using hardware provided. Reed switch mounting
locations can be moved to one of the four positions shown in Fig. 2. If mounted next to
door, route reed switch wire through knockout in bottom of housing as shown in Fig. 3.
6. Mount magnet on door frame (or door
if unit is mounted next to door) using
screws provided. When mounting on
metal doors or door frames, use plastic
spacers provided. Reed switch and
magnet must be within 3/4” when door
is closed (3/8” on metal door and frame).
Please refer to figures 4, 5 and 6 on page
6 for other mounting options.
7. If installing STI-6402, STI-6403, or
STI-6404 continue to page 7 for more
instructions (Fig. 7 and 8). STI-6402
mounting option is shown on page 6.
8. Replace cover by sliding flanges on
inside of cover into slots on base. Then
rotate the cover over unit and snap close.
Replace tamper screw.
Note: STI recommends setting up unit and testing settings prior to mounting.
Figure 3
POLYCARBONATE COVER
POLYCARBONATE BASE
120 dB HORN
ALARM DURATION
ALARM TRIP DELAY
EXIT DELAY
VOLUME
VIEW OF THE CIRCUIT BOARD
19039 SCREW
6 x 1 1/4 in.
(2) PROVIDED
19018 ANCHOR
(2) PROVIDED
BOTTOM SURFACE AS SHOWN
WIRES THROUGH NOTCH ON
AND ROUTE REED SWITCH
REMOVE FRONT COVER
VIEW SHOWING MAGNET INSTALLATION
MAGNET
NC COM NO GD V+ RS1 RS2 KEYSW
TERMINAL BLOCK WIRING CONNECTIONS
FORM
C
DRY CON
TACTS
R
EMOT
E
POWE
R
INPU
T
9-24
VD
C
R
EE
D
SW
ITCH
TE
R
M
IN
ALS
KE
Y
SW
ITCH
TE
R
M
IN
ALS
INTERNAL REED SWITCH
(RS1)
ALARM DURATION
ALARM TRIP DELAY
EXIT DELAY
VOLUME
VIEW OF THE CIRCUIT BOARD
MAXIMUM GAP 3/4 in. (19mm)
3/8 in. (9.5mm) ON METAL DOOR
AND FRAME
SPACERS (USE AS NECESSARY)
NOTE: 2 SPACERS UNDER BOTH
MAGNET AND REED SWITCH
MUST BE USED ON STEEL DOORS
4
3
2
1
NC COM NO GD V+ RS1 RS2 KEY SW
SLOTS
FLANGES
TERMINAL STRIP
9 VOLT BATTERY
19011 TAMPERPROOF SCREW
(1) PROVIDED
19016 TAMPER WRENCH
(1) PROVIDED
BASE
19014 MOUNTING SCREW
(4) PROVIDED
REED SWITCH
MOUNTING LOCATIONS
(LABELED 1-4)
COVER
NC COM NO GD V+ RS1 RS2 KEY SW
4
3
2
1
NC COM NO GD V+ RS1 RS2 KEY SW
SLOTS
FLANGES
TERMINAL STRIP
9 VOLT BATTERY
19011 TAMPERPROOF SCREW
(1) PROVIDED
19016 TAMPER WRENCH
(1) PROVIDED
BASE
19014 MOUNTING SCREW
(4) PROVIDED
REED SWITCH
MOUNTING LOCATIONS
(LABELED 1-4)
COVER
4
3
2
1
ALARM SOUNDS WHEN DOOR IS OPENED
EMERGENCY USE ONLY
ON OFF
NC COM NO GD V+ RS1 RS2 KEY SW
SLOTS
FLANGES
TERMINAL STRIP
9 VOLT BATTERY
19011 TAMPERPROOF SCREW
(1) PROVIDED
19016 TAMPER WRENCH
(1) PROVIDED
BASE
19014 MOUNTING SCREW
(4) PROVIDED
REED SWITCH
MOUNTING LOCATIONS
(LABELED 1-4)
COVER
TO KEY
SWITCH
06402 REED SWITCH
(RS2)
OPTIONAL:
TO REMOTE
HORN
STI-6403
TERMINAL BLOCK
VIEW SHOWING INSTALLATION OF
ADDTIONAL REED SWITCH 06402
3/4 in. (19mm)
MAXIMUM GAP
3/8 in. (9.5mm) ON
METAL DOOR AND FRAME MAGNET ASSEMBLY
(SEE ABOVE FOR INSTALLATION)
DOOR
SWING
6400 SWING
MAGNET
DOOR STOP
MAGNET MUST BE
INSTALLED OPPOSITE
RAISED RIB ON OUTER COVER 19039 SCREW
6 x 1 1/4 in.
(2) PROVIDED
SPACERS - USE
AS NECESSARY NOTE: (2) SPACERS MUST BE
USED ON STEEL DOORS
19018 ANCHOR
(2) PROVIDED
MAGNET
6400 UNIT
DOOR
SWING
JAM
DOOR STOP
DOOR
TYPICAL FLUSH MOUNT DOOR JAM
INSTALLATION
TYPICAL RECESSED MOUNT DOOR JAM
INSTALLATION
POLYCARBONATE COVER
POLYCARBONATE BASE
120 dB HORN
ALARM DURATION
ALARM TRIP DELAY
EXIT DELAY
VOLUME
VIEW OF THE CIRCUIT BOARD
19039 SCREW
6 x 1 1/4 in.
(2) PROVIDED
19018 ANCHOR
(2) PROVIDED
BOTTOM SURFACE AS SHOWN
WIRES THROUGH NOTCH ON
AND ROUTE REED SWITCH
REMOVE FRONT COVER
VIEW SHOWING MAGNET INSTALLATION
MAGNET
NC COM NO GD V+ RS1 RS2 KEYSW
TERMINAL BLOCK WIRING CONNECTIONS
FORM
C
DRY CON
TACTS
R
EMOT
E
POWE
R
INPU
T
9-24
VD
C
R
EE
D
SW
ITCH
TE
R
M
IN
ALS
KE
Y
SW
ITCH
TE
R
M
IN
ALS
INTERNAL REED SWITCH
(RS1)
ALARM DURATION
ALARM TRIP DELAY
EXIT DELAY
VOLUME
VIEW OF THE CIRCUIT BOARD
MAXIMUM GAP 3/4 in. (19mm)
3/8 in. (9.5mm) ON METAL DOOR
AND FRAME
SPACERS (USE AS NECESSARY)
NOTE: 2 SPACERS UNDER BOTH
MAGNET AND REED SWITCH
MUST BE USED ON STEEL DOORS
4
3
2
1
NC COM NO GD V+ RS1 RS2 KEY SW
SLOTS
FLANGES
TERMINAL STRIP
9 VOLT BATTERY
19011 TAMPERPROOF SCREW
(1) PROVIDED
19016 TAMPER WRENCH
(1) PROVIDED
BASE
19014 MOUNTING SCREW
(4) PROVIDED
REED SWITCH
MOUNTING LOCATIONS
(LABELED 1-4)
COVER
NC COM NO GD V+ RS1 RS2 KEY SW
4
3
2
1
NC COM NO GD V+ RS1 RS2 KEY SW
SLOTS
FLANGES
TERMINAL STRIP
9 VOLT BATTERY
19011 TAMPERPROOF SCREW
(1) PROVIDED
19016 TAMPER WRENCH
(1) PROVIDED
BASE
19014 MOUNTING SCREW
(4) PROVIDED
REED SWITCH
MOUNTING LOCATIONS
(LABELED 1-4)
COVER
4
3
2
1
ALARM SOUNDS WHEN DOOR IS OPENED
EMERGENCY USE ONLY
ON OFF
NC COM NO GD V+ RS1 RS2 KEY SW
SLOTS
FLANGES
TERMINAL STRIP
9 VOLT BATTERY
19011 TAMPERPROOF SCREW
(1) PROVIDED
19016 TAMPER WRENCH
(1) PROVIDED
BASE
19014 MOUNTING SCREW
(4) PROVIDED
REED SWITCH
MOUNTING LOCATIONS
(LABELED 1-4)
COVER
TO KEY
SWITCH
06402 REED SWITCH
(RS2)
OPTIONAL:
TO REMOTE
HORN
STI-6403
TERMINAL BLOCK
VIEW SHOWING INSTALLATION OF
ADDTIONAL REED SWITCH 06402
3/4 in. (19mm)
MAXIMUM GAP
3/8 in. (9.5mm) ON
METAL DOOR AND FRAME MAGNET ASSEMBLY
(SEE ABOVE FOR INSTALLATION)
DOOR
SWING
6400 SWING
MAGNET
DOOR STOP
MAGNET MUST BE
INSTALLED OPPOSITE
RAISED RIB ON OUTER COVER 19039 SCREW
6 x 1 1/4 in.
(2) PROVIDED
SPACERS - USE
AS NECESSARY NOTE: (2) SPACERS MUST BE
USED ON STEEL DOORS
19018 ANCHOR
(2) PROVIDED
MAGNET
6400 UNIT
DOOR
SWING
JAM
DOOR STOP
DOOR
TYPICAL FLUSH MOUNT DOOR JAM
INSTALLATION
TYPICAL RECESSED MOUNT DOOR JAM
INSTALLATION
Figure 2