Edwards Signaling 5541M-Y6 - Manual (Page 2)

P/N 3100471 ISSUE 3 PAGE 2
DEVELOPED BY EDWARDS SIGNALING
COPYRIGHT NOTICE
© 2003
IMPORTANT IMFORMATION
Limitation of liability
This product has been designed to meet the requirements of Underwriters
Laboratories, Inc., Standard 2017 and 864. Installation in accordance with
this manual, applicable codes, and the instructions of the Authority Having
Jurisdiction is mandatory. The manufacturer shall not under any
circumstances be liable for any incidental or consequential damages
arising from loss of property or other damages or losses owing to the
failure of products beyond the cost of repair or replacement of any
defective products. The manufacturer reserves the right to make product
improvements and change product specifications at any time.
While every precaution has been taken during the preparation of this
manual to ensure the accuracy of its contents, the manufacturer assumes
no responsibility for errors or omissions.
FCC Warning
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
to cause harmful intereference in which case the user will be required to
correct the interference at his own expense.
Compliance Statement
Millennium System Master, when properly installed, operates with a Local
Protected Premises Fire Alarm System in accordance with the following
standard:
•
Underwriters Laboratories Standard 864
Millennium System Master, when properly installed, can also be
configured to operate as a self-monitored evacuation device, in
accordance with the following standard:
•
Underwriters Laboratories Standard 2017
Content
Chapter 1 System overview and operation 1
1.1 System overview .................................................................. 1
1.2 Operations Review ............................................................... 1
1.3 Controls and Indicators ....................................................... 1
1.4 Operating the Panel ............................................................. 5
Chapter 2 Installation 7
2.1 Installation checklist ............................................................ 7
2.2 Installing the cabinet ........................................................... 7
2.3 Installing Power .................................................................. 7
2.4 Wiring a Satellite Panel ..................................................... 10
2.5 Connecting Speaker/Amplifiers ......................................... 11
2.6 Connecting External Initiating Inputs ................................. 11
2.7 Connecting to Output Relay ............................................... 12
2.8 Connecting External Initiating Input to Fire
Alarm Panel ....................................................................... 12
2.9 Connecting to a UL Listed Telephone Access
Module .............................................................................. 13
2.10 Connecting to Remote Paging Units .................................. 14
2.11 Adjusting Audio Levels ..................................................... 15
Chapter 3 Programming 16
3.1 Overview ............................................................................ 16
3.2 Local Alarm Input Assignment .......................................... 16
3.3 Relay Output Assignment .................................................. 16
3.4 Device Commission ........................................................... 16
3.5 Dynamic Zone Control TM
...........................................................................................
17
3.6 Communications Setup ..................................................... 17
3.7 Panel Address Assignment ................................................ 17
3.8 Panel Mode ....................................................................... 17
3.9 Auto Learn Mode ............................................................... 17
3.10 Zone to Input Assignment ................................................. 18
3.11 Voice Message Setup ........................................................ 18
3.12 Standby Power Mode ........................................................ 19
3.13 Remote Programming ...........................................................
3.14 Text Output String .................................................................
3.15 Security ............................................................................. 19
Chapter 4 Maintenance 20
4.1 Preventive Maintenance ..................................................... 20
4.2 Preventive Maintenance Schedule ..................................... 20
Chapter 5 LCD Messages and Troubleshooting 21
5.1 Normal Mode ..................................................................... 21
5.2 Troubleshooting and Trouble Messages ............................ 22
Appendix A Calculations 26
Battery calculation worksheet ........................................................ 26
5532M Audio amplifier voltage drop calculation ........................... 27
5532M Audio am. circuit max. wire length calculation ................. 28
Suggested RS-485 Network topology ........................................... 28
Appendix B Programming template 29
Appendix C Panel specifications 30
Appendix D Wiring 31