Audient iD22 - Manual (Page 13)

21 22
Software Features
Stereo Linking
All channels can be linked or un-linked for
stereo or mono operation. Level controls
are ganged in stereo operation but stereo
panoramic positioning control remains
individual for left and right channels.
Useful Functionality
Every active control
(buttons, pots or
faders) in the iD mixer
application feature
colour coded mouse
over indicators to help
you quickly navigate
and make adjustments.
All controls are also
scroll-wheel enabled in
the iD mixer application.
Channel Strip Controls
• Unlinked
• Individual Level
• Individual Pan • Linked
• Ganged Level
• Individual Pan
Cue A Send Controls
Level (0 dB to off)
Pan (if using stereo cue)
Alt (⌥) + click to zero
Cue B Send Controls
Level (0 dB to off)
Pan (if using stereo cue)
Alt
(⌥) + click to zero
Parameter Info Box
Normally displays main
channel pan value but
if you hover the mouse
over any control - it will
display that parameter’s
value so you can see
what’s what
Channel Solo & Cut
Latching operation
Command (⌘) + click
on a solo switch, while on
an un-solo’d channel will
override any previously
solo’d channel
Command (⌘) + click
on an already activated
solo switch will clear all
solo’d channels
Channel Meter
66dB Range
Separate Peak Hold Indicator
Click on peak indicator to clear
Alt
(⌥) + click to clear all
Channel Fader
+6dB to off
Alt
(⌥) + click to zero
Channel Tape Label
EDITABLE - 8 characters
Master Section
Software Features
Cue Masters
Level (0 dB to off)
Controls output level
of all summed cue sends
Alt
(⌥) + click to zero
Cue Master Solos
Use these cue solos
to audition artist mixes
quickly. They operate in
a interlocked fashion so
only one can be solo’d at
a time
Talkback Button
Operating the talkback
switch routes whichever
input has been selected as
talkback (in system panel)
to both cue A & B (level set
by talkback channel cue
send levels) and to your
DAW. This way talkback
can be sent directly to
artists or via the DAW to a
record enabled or input
monitored track (SLATE
mode)
Monitor Dim & Cut Buttons
DIM auto-triggered by
talkback. Level programmed
in system panel.
Permanently controlled by
hardware switches
Channel View Buttons
Customise your mixer
layout by including only the
channels you are using
Not using the digital i/o?
Hide it
Mixing / listening back and
want to hide most of the
GUI? You can
Show / hide when required
Main Meters
66 dB Range
These meters indicate the
output levels of the DSP mix
bus within iD22. They are
mirrored by the 4-segment
hardware LED meters on the
main unit
1dB steps from 0 to-6dBFS
2dB steps from -8 to -56dBFS
Separate Peak Hold Indicator
Click on peak indicator to clear
Alt
(⌥) + click peak to clear
System Panel Button
Opens the iD22 set-up and
routing matrix panel
(see page 27)
Mono Sum Button
Monitor the output
of the iD22 DSP mixer
summed to mono
Assign to ‘F’ key > right click &
select F1, F2 or F3
Polarity Reverse Button
Invert polarity of one side
of the stereo monitor output
for stereo difference checks
Assign to ‘F’ key > right click &
select F1, F2 or F3
Hardware Volume
Control Only
Alt. Loudspeaker Button
Switch to alternative
monitors if set-up in system
panel matrix as out 3+4
Assign to ‘F’ key > right click &
select F1, F2 or F3