Alpine MOBILE MULTIMEDIA STATION IVA-D900 - Manual (Page 35)

33
-EN
Navigation Interruption and Adjusting its Volume
Setting item: NAV.MIX
Setting content: OFF / ON
With an Alpine navigation system connected to the IVA-D900, the
voice guidance of the navigation system will be mixed with the radio
or CD play. You can adjust the volume level of the voice guidance.
OFF: The navigation interruption mode is turned off.
ON:
The navigation interruption mode is on.
1) After setting it to ON, press the Rotary encoder to select
NAV.MIX mode.
VOL.
→ NAV. → SUB W. → BAL. → FAD. → DEFEAT →
VOL.
2) Turn the Rotary encoder to adjust the volume (0 to 15) of
the navigation voice.
• The audio volume during the navigation guide can be set by
adjusting the audio volume while the navigation guide continues.
When the navigation guide finishes, the previous audio volume and
the previous screen are restored. For exception, if the navigation
cuts in when the audio volume is lower than the setting level, the
audio volume during the navigation guide is reset the current
listening volume. (When the navigation guide cuts in, the audio
volume does not increase.)
• This setting is effective when NAV.IN of SYSTEM list screen is ON.
• When PXA-H510 or PXA-H900 is connected, NAV.MIX value set in
this unit does not affect PXA-H510 or PXA-H900.
Setting the Navigation Mode
When you connect an optional navigation equipment, set it to ON.
Setting item: NAV. IN
Setting contents: OFF / ON
ON: Navigation source is displayed.
OFF: Navigation source is not displayed. The settings
related to the navigation can not be changed from this
unit.
Setting the AUX Mode
Setting item: AUX IN 1, 2, 3
Setting content: OFF / LEVEL LOW / HIGH
OFF: AUX source is not displayed.
LEVEL LOW/HIGH:
The sound volume from the external equipment can be
adjusted. When LOW or HIGH is selected, AUX source
will be ON.
• OFF is not displayed when the optional DVD player or DVD
changer is connected.
• When OFF is selected, the settings related to AUX can not be
changed from this unit (except for “Name external equipment to be
displayed” page 34).
• When either DVD player or DVD changer is connected to AUX IN
1, DVD is displayed on the screen. When both of them are
connected, DVD is displayed for AUX IN 1 and DVD CHG is
displayed for AUX IN 2.
System Setup Operation
To display the System mode screen:
To watch a video source, your vehicle must be parked with
the ignition key in the ACC or ON position. To do this, follow
the procedure below.
1. Brake to bring your vehicle to a complete stop at a
safe location. Engage the parking brake.
2. Keep pushing the foot brake and release the parking
brake once then engage it again.
3. When the parking brake is engaged for the second
time, release the foot brake.
• For automatic transmission vehicles, place the transmission
lever in the Park position.
Now, the locking system for the System mode operation has
been released. Engaging the parking brake can reactivate
the System mode, as long as the car's ignition has not been
turned off. It is not necessary to repeat the above
procedure (1 through 3), of “To display the System mode
screen.”
Each time the ignition is turned OFF, perform the procedure
of “To display the System mode screen.”
The following steps 1 to 6 are common operations to each
“Setting item” of SYSTEM Setup. Refer to each section for
details.
1
Press SOURCE/POWER.
The main menu is displayed.
2
Press 6 (SETUP).
The Setup mode screen appears.
3
Turn the Rotary encoder to select “SYSTEM,”
then press the Rotary encoder.
The SYSTEM list is displayed.
4
Turn the Rotary encoder to select your desired
setting item.
The screen shows the ∗Function Guide.
* Displays the function assigned for each button (the Function
buttons).
Setting items:
NAV.MIX ↔ NAV.IN ↔ AUX IN1 ↔ AUX IN2 ↔ AUX IN3
↔ AUX IN1 MODE ↔ AUX IN2 MODE ↔ AUX IN3 MODE
↔ CAMERA IN ↔ MONITOR OUT1 ↔ MONITOR OUT2
↔ IN-INT MUTE ↔ IN-INT ICON ↔ A.PROC TYPE
5
Press the function buttons to switch the setting.
6
Press 7 (RETURN).
The screen returns to the previous one.
• With the System screen displayed, pressing and rotating the rotary
encoder will adjust the volume level.
• Immediately after inputting titles or changing the settings of
System Mode (While the system is inputting the titles or data
automatically) do not turn the ignition key (engine key) to OFF.
Otherwise, a title may not be written, or the settings may not be
changed.
Continued