HP XP Array Manager Software - Manual (Page 63)

Return Codes, Output Messages, and Error Codes 5-9
Hitachi Cache Manager User’s Guide
Error
Number
Error Message Recommended Action
JSE307I-E I/O ERROR job name,
step name, disk drive
unit number, device
type, dd name, order,
error type, BBCCHHR,
QSAM I/O error has been detected during the output operation of the COUNTS or STATUS
command. See “SYNADAF macro” explanation for more detail.
(S) Terminate the command process, but the next process continues. (Return code is 8.)
(P) Examine the error message.
JSE500I-U INVALID RAIDPARM
PARAMETER The specified contents of the dataset in RAIDPARM DD statement has a coding rule error.
(S) HRUDCRX terminates abnormally. (Return code is 16.)
(P) Correct the error and execute the command again.
JSE501I-U DEVICE NUMBER
EXCEEDS LIMIT The total number of disk drive units specified by the dataset in the RAIDPARM DD
statement exceeds the maximum.
(S) HRUDCRX terminates abnormally. (Return code is 16.)
(P) Correct the error and execute the command again.
JSE502I-W ‘disk drive unit number’
IS DUPLICATED The dataset in RAIDPARM DD statement includes a duplicated disk drive unit number.
(S) Ignore the duplicated parameter, and the process continues. (Return code is 4.)
JSE503I-W ‘disk drive unit number’
IS NOT IN CACHE
SUBSYSTEM The disk drive unit number specified by the dataset in RAIDPARM DD statement does not
exist in this cache storage system.
(S) Terminate the process for this disk drive unit, but the process continues for the
following disk drive units. (Return code is 4.)
JSE504I-W ‘disk drive unit number’
IS NOT ONLINE The disk drive unit number specified by the dataset in RAIDPARM DD statement is either
not online or not mounted in the cache storage system.
(S) Terminate the process for this disk drive unit, but the process continues for the
following disk drive units. (Return code is 4.)
JSE505I-W RAIDPARM IS EMPTY The dataset specified by RAIDPARM DD statement has no record.
(S) The process continues. (Return code is 4.)
JSE506I-S I/O ERROR ON ‘disk drive
unit number’ An input/output error happened during the I/ O operation to the cache storage system of
the disk drive unit number specified by the dataset in RAIDPARM DD statement.
(S) If you are specifying the DKC parameter by a STATUS command or a COUNTS
command, terminate the process for the volume, but the process continues for the
following volumes. (Return code is 12.)
(P) If another system has some error messages, review them, address the problem(s),
then execute the command again.
JSE507I-S I/O ERROR ON ‘disk drive
unit number’, ‘sense
byte’ An input/output error happened during the I/O operation to the cache storage system of
the disk drive unit number specified by the dataset in RAIDPARM DD statement.
(S) If you are specifying the DKC parameter by a STATUS command or a COUNTS
command, terminate the process for that volume, but the process continues for the other
volumes. (Return code is 12.)
(P) Examine the contents of the message and correct the error, then execute the
command again.
JSE510I-S DATASET ‘dataset name’
EXTENT FROM CCHH TO
CCHH IS [BOUND,
UNBOUND or NOT
CHANGE]. The utility indicates (hexadecimal) that the resident extents of the dataset specified by
DATASET parameter were not processed. In case that an input/output error to the cache
storage system happened during the operation, the utility prints out the status of all
dataset extents.
BOUND: The extents reside in cache memory.
UNBOUND: The extents do not reside in cache memory.
NOT CHANGE: The extents have not changed from the previous command, because the
process was not executed.
(S) HRUDCRX terminates abnormally. (Return code is 12.)
(P) Examine the contents of the message and correct the error, then execute the
command again.