Phottix Mitros for Nikon - Manual (Page 14)

14
En INSTRUCTION MANUAL
Quick Flash Function
The Quick Flash function allows the flash to fire at 1/6 to 1/2 of the full output.
Quick Flash recycle times are faster. It helps for snap photography for near sub-
jects.
Quick flash can be used for continuous drive modes, quick flash for continuous
shot function can be enabled or disabled (see C.Fn-06 above).
Please note:
The Quick Flash Function makes flash firing a priority. Under-exposure could
result if the subject is located too far from the camera.
Auto Backlight
The backlight will light up for 8 seconds and then go off if no buttons are
pressed. When the auto backlight function is enabled, pressing any button will
light it up after it goes off. When the auto backlight function is set to “disable”,
pressing the mode button will light it up.
Slave Flash Beep Confirm
When the flash is used as a wireless Slave it will beep twice when a triggering
signal is received from the Master Flash. This can be disabled (see C.Fn 04 above).
Built-in Camera AF-assist Light
1. The Mitros+ flash’s AF-assist light will take priority over a built-in camera AF
Assist light. The camera’s AF-assist light will not function when the Phottix Mi-
tros+ is on the camera.
2. To use the camera’s AF-assist illuminator disable the flash’s AF-assist light (see
C.Fn 08 above).
Choose the FX/DX
The Phottix Mitros+ can automatically select the applicable flash illumination
pattern according to the camera’s image area. When the flash is attached to a
camera that features FX format (36 × 24) or DX format (24 ×16) the pattern will
change . For more information, see your Camera’s User Manual. FX / DX Flash
Zoom range can be manual set in the Mitros+ Custom Functions (see C.Fn 09
above) to meet different shooting needs.
Button Beep Confirm
Using the Phottix Mitros+ buttons provides audible feedback – beeps – when
each is pressed. This function can be turned off (see C.Fn 13 above).
TTL Pref
TTL may vary slightly when using the flash on different cameras. TTL Pref (C.Fn-
15) setting allows users to adjust EV from +3 to -3 in 1/3rd stops to compensate
for these slight variations. This adjustment is a personal preference based on
camera standard TTL and will be stored in memory. When this EV level prefer-
ence is set, this compensation will be used for images taken in TTL mode. This EV
compensation will not be displayed on the LCD during regular use.
Memory Function
The Phottix Mitros+ Flash is equipped with a programmable Memory function.
Using the Memory Function allows flash parameters, data and custom functions
to be saved and quickly recalled for future use. Flash modes, wireless settings,
flash power – all the current programming of the flash will all be saved for later
use.
Memory Mode Screen
Menu:
Three saved data and three recall locations are available in Memory Mode:
SAVE TO 1
SAVE TO 2
SAVE TO 3
LOAD FROM 1
LOAD FROM 2
LOAD FROM 3
To enter Memory Mode
Press and hold button to enter the Memory Mode.
To save data:
1. After setting flash data, press and hold the button to enter the
Memory mode.
2. Press the and buttons to select a save location: SAVE TO 1,
SAVE TO 2 and SAVE TO 3.
3. Press the button to confirm the location and save the data.
4. The LCD display will exit the Memory Mode screen and return to the last
used screen.
5. To cancel the save action, press the button to exit the Memory Mode
screen and return to the last used screen.
To recall data:
1. After entering the Memory mode (see above), Press the and
buttons to select LOAD FROM 1, LOAD FROM 2. LOAD FROM 3.
2. Press the button will recall the saved data from the selected location.
Please note:
After recalling saved data and exiting the memory mode, the recalled data
will be displayed on the screen. Flash setting used before recalling data will
be lost. To avoid losing data save current setting before recalling saved data.