A.J. Antunes & Co ES-1200 9300588 - Manual (Page 12)

egg station
12 P/N 1011004 Rev. B 08/08
TRoUblesHooTInG (continued)
control board leDs
The Control Board has three on board LEDs (Figure 8)
to determine the status of the unit and to assist in
troubleshooting.
Green (Diagnostic): This LED should be off in nor-
mal operation. However, if any of the 5 potential faults
are detected by the Control Board, this LED will blink
repeatedly either 1 through 5 times with a 2 second
pause in between. See the green LeD Blink Codes
section below.
yellow (audio): When lit, this LED indicates that the
Control Board is supplying approximately 10-15 VDC to
the audio signal. The audio signal should sound when
this LED is lit.
Red (Heat): When lit, this LED indicates that the
Control Board is calling for heat by supplying VDC to
the Solid State relay terminals 3(+) and 4(-). When off,
this means that the Grill Surface is up to operating
temperature and satisfied.
Green leD blink codes
number of
blinks
cause(s) Unit’s state and Resolution
The Green LED
blinks on and off
1 time, pauses for
2 seconds, and
repeats.
Control Board’s EEPRoM memory is
corrupted.
In this state, the unit turns off the control signal to the Solid
State Relay and disables all front buttons and front lights.
The unit will not heat up. This continues until the defaults are
reloaded into the memory. To reload the defaults, turn the unit
off, press and hold the Time 2 button, turn the unit back on,
and then release the button.
The Green LED
blinks on and off
2 times, pauses
for 2 seconds, and
repeats.
The ambient temperature within the con-
trol compartment has exceeded 68ºC
(155ºF). Verify that the unit has proper
air ventilation all around it and that it is
not near a significant heat source.
In this state, the unit turns off the control signal to the Solid
State relay and disables all front buttons and front lights. The
unit will not heat up. This continues until the ambient tem-
perature within the electrical compartment drops below 60ºC
(140ºF) and the unit is turn off and turned on again.
The Green LED
blinks on and off
3 times, pauses
for 2 seconds, and
repeats.
open or disconnected Thermocouple. In this state, the unit turns off the control signal to the Solid
State Relay and disables all front buttons and front lights. The
unit will not heat up. This continues until the Thermocouple is
reconnected or replaced and the unit is turned off and turned
on again.
The Green LED
blinks on and off
4 times, pauses
for 2 seconds, and
repeats.
Supply voltage to the unit is below 160
VAC or above 265 VAC.
In this state, the unit turns off the control signal to the Solid
State Relay and disables all front buttons and front lights. The
unit will not heat up. This continues until the supply voltage is
within the proper limits and the unit is turned off and turned on
again.
The Green LED
blinks on and off
5 times, pauses
for 2 seconds, and
repeats.
The 50/60 Hz signal has been lost due
to a loose, disconnected, or open wire
harness/wiring on the AC Isolator Board,
or from the AC Isolator Board to the
Control Board.
In this state, the unit turns off the control signal to the Solid
State Relay and disables all front buttons and front lights. The
unit will not heat up. This continues until the 50/60 Hz signal is
reapplied and the unit is turned off and turned on again.
noTe: During heat mode, this Red leD is very dim,
so it may be difficult to verify if the control board
is or is not calling for heat. It is recommended
that you observe the small round green leD on the
solid state Relay (figure 9) for mode and diagnos-
tic purposes. When the green leD on the solid
state Relay is on, it means that the control board is
calling for heat. When off, it means that the control
board is noT calling for heat.
figure 8. control board
leDs
figure 9. solid state
Relay
R
PRODUCT SERVICE
TUV
. gapruit Bauart
Crouzet
GN
84137220
4/A2-
3-32 VDC
+3/A1
1/L1 2/T1
50 AMP 24-280 VAC
Solid State
Relay
LED
HEAT
BUZZ
STATUS
CR4
CR3
CR5 YELLOW
GREEN
RED
R17
R20
R18