Karcher KM 90-60 R P - Manual (Page 21)

- 5
ƽ
Danger
Risk of injury and damage! Do not use a
forklift to unload the appliance.
To unload the machine, proceed as follows:

Cut plastic packing belt and remove foil.
 Fill battery with battery acid (see sec-
tion on Care and Maintenance).
 Install the battery and connect it (see
section on Care and Maintenance).
 Remove the elastic tape fasteners at
the stop points.
 Four indicated floor boards of the pallet
are fastened with screws. Unscrew
these boards.
 Place the boards on the edge of the pal-
let. Place the boards in such a way that
they lie in front of the four wheels of the
machine. Fasten the boards with
screws.
 Slide the four support beams included
in the packaging under the ramp.
 Remove the wooden blocks used for ar-
resting the wheels and slide them under
the ramp.
 Slide the machine over the prepared
ramp from the pallet.
The machine can be moved in 2 ways:
(1) By pushing it (see Moving sweeper
without engaging self-propulsion).
(2) By driving it (see Moving sweeper by
engaging self-propulsion).
ƽ Danger
Risk of injury! Before engaging the free-
wheel operation, the machine must be se-
cured to prevent it rolling away.

Open the device hood.
 Set the freewheel lever to OFF.
Note: If the freewheel lever does not lock
in, then slightly move the machine forward
and backward.
– This blocks the travel drive function.
– Braking effect exists no more.

Close cover.
The machine can now be pushed.
Note: Do not move the machine for long
distances without engaging self-propul-
sion, a speed of 6 km/h should not be ex-
ceeded.
 Set the freewheel lever to ON.
The travel drive is now ready for operation.

Close cover.
The appliance can now be driven.
Note: The machine has been fitted with an
automatic parking brake that is activated as
soon as the engine is switched off and the
driver leaves his seat.

Park the sweeper on an even surface.
 Remove ignition key.
ƽ
Danger
Risk of explosion!
– Only use the fuels specified in the Op-
erations Manual.
– Do not refuel the machine in enclosed
spaces.
– Smoking and naked flames are strictly
prohibited.
– Ensure that no fuel reaches the hot
open surfaces.
– Overflown fuel can form an explosive
misture of fuel and air when it comes in
contact with the blower.
 Switch off engine.
 Open the device hood.
 Open fuel filler cap.
 Insert funnel.
 Use "regular unleaded petrol".
 Fill tank to max. 1 cm below the lower
edge of the filler nozzle.
 Wipe off any spilt fuel, remove funnel
and close fuel filler cap.
 Close cover.
Note: The contents of the tank are suffi-
cient to operate the machine for about an
hour.
 Check engine oil level.
 Check fill level of fuel tank.
 Check fill level of hydraulic oil.
 Check side brush.
 Check roller brush.
 Shake off dust filter.
 Empty waste container.
 Check tyre pressure.
Note: For description, see section on Care
and maintenance.
Caution
Risk of damage to the axle! Before each
drive, check and ensure that the free-run
lever is at ON position.
Caution
The air inlets next to the driver's seat must
not be covered. Do not store any objects
next to or behind the seat.
 Pull seat adjustment lever inwards.
 Slide seat, release lever and lock in
place.
 Check that the seat is properly locked in
position by attempting to move it back-
wards and forwards.
Note: The max. load of the storage area is
20 kg.

Fasten the load through appropriate
fasteners at the 4 eyelets.
1 Driving
Driving to the Place of Use.
2 Sweeping with sweep roller
Roller brush is lowered.
3 Sweeping using roller brush and side
brushes
Roller brush and side brushes are low-
ered.
Note:The machine is equipped with a seat
contact switch If the driver's seat is vacat-
ed, the machine is switched off.
Note: If the seat contact switch has
switched off the machine, then turn the ig-
nition key to "0" to prevent battery dis-
charge.
 Open the device hood.
Before Startup
Unloading
Moving sweeper without engaging
self-propulsion
Moving sweeper by engaging self-
propulsion
Start up
General notes
Refuelling
Inspection and maintenance work
Operation
Adjusting driver's seat
Storage area
Programme selection
Starting the machine
Open fuel cock
21 EN