Asus AP1600R-E2 - Manual (Page 52)

C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n 4 - 1 0 4 - 1 0 4 - 1 0 4 - 1 0 4 - 1 0
4 . 4 . 4 . 4 . 4 . H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D 1 ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D 1 ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D 1 ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D 1 ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 2 - p i n H D L E D 1 )
This connector supplies power to the hard disk activity LED. The read
or write activities of any device connected to the primary/secondary
IDE connectors or the SATA connectors cause this LED to light up.
NCLV-D
NCLV-D
SCSI/SATA card activity LED connector
HDLED1
1
SCSI_ACTLED-
SCSI_ACTLED+
SCSI_ACTLED-
SCSI_ACTLED+
5 . 5 . 5 . 5 . 5 . S y s t e m f a n c o n n e c t o r s ( R E A R _ F A N 1 / 2 , F R N T _ F A N 1 / 2 ) S y s t e m f a n c o n n e c t o r s ( R E A R _ F A N 1 / 2 , F R N T _ F A N 1 / 2 ) S y s t e m f a n c o n n e c t o r s ( R E A R _ F A N 1 / 2 , F R N T _ F A N 1 / 2 ) S y s t e m f a n c o n n e c t o r s ( R E A R _ F A N 1 / 2 , F R N T _ F A N 1 / 2 ) S y s t e m f a n c o n n e c t o r s ( R E A R _ F A N 1 / 2 , F R N T _ F A N 1 / 2 )
The fan connectors support cooling fans of 350 mA ~ 740 mA (8.88 W
max.) or a total of 2.1 A ~ 4.44 A (53.28 W max.) at +12V. Connect
the fan cables to the fan connectors on the motherboard, making sure
that the black wire of each cable matches the ground pin of the
connector.
Do not forget to connect the fan cables to the fan connectors.
Insufficient air flow inside the system may damage the motherboard
components. These are not jumpers! Do not place jumper caps on the
fan connectors!
NCLV-D
NCLV-D Fan connectors
GND
Rotation
+12V
REAR_FAN2 REAR_FAN1
FRNT_FAN1 FRNT_FAN2
GND Rotation +12V
REAR_FAN2
REAR_FAN1
FRNT_FAN1
FRNT_FAN2
GND
Rotation
+12V GND
Rotation
+12V