Panasonic SCHC15EP - Manual (Page 7)

RQTX1246
7
E
N
G
L
IS
H
ENGL
ISH
7
Clock and timers
Setting the clock
This is a 24-hour clock.
1 Press [CLOCK/TIMER] to select “CLOCK”.
2 Within 10 seconds, press [R, T] to set the time.
3 Press [OK].
Press [CLOCK/TIMER] to show the clock for a few seconds.
Note:
Reset the clock regularly to maintain accuracy.
Sleep timer
The sleep timer switches off the system after the set time.
Press [SLEEP] to select the setting (in minutes).
To cancel, select “OFF”.
30 MIN OFF → 120 MIN → → 60 MIN → 90 MIN
To show the remaining time
Press [SLEEP].
Note:
• The sleep timer can be used together with the play timer.
• The sleep timer always comes first. Be sure not to set an overlap of
timers.
Play timer
You can set the timer to come on at a certain time to wake you up.
Switch on the system and set the clock.
Prepare the music source you want to listen to (disc, radio, USB or
AUX) and set the volume.
1 Press [CLOCK/TIMER] to select “#PLAY 1”, “#PLAY 2” or
“#PLAY 3”.
2 Within 10 seconds, press [R, T] to set the start time.
3 Press [OK].
4 Do steps 2 and 3 again to set the end time.
To start the timer
5 Press [#, PLAY] to start “#PLAY 1”, “#PLAY 2” or “#PLAY 3”.
6 Press [`] to switch off the system.
The system must be switched off for the timer to operate.
Change the
settings Do steps 1 through 4 and 6 again (Z above).
Change the
source or
volume 1) Press [#, PLAY] two times to remove the timer
indicator on the display panel.
2) Change the source or volume.
3) Do steps 5 and 6 (Z above).
Check the
settings Press [CLOCK/TIMER] to select “#PLAY 1”,
“#PLAY 2” or “#PLAY 3”.
Cancel Press [#, PLAY] two times to remove the timer
indicator on the display panel.
Note:
• The play timer starts at a low volume and increases gradually to the
preset level.
• The timer comes on at the set time every day if the timer is on.
• If you switch off the system and switch on again while a timer is in
operation, the timer will not stop at the end time.
RDS broadcasting
This system can show the text data transmitted by the radio data
system (RDS) available in some areas.
Press [ DISPLAY].
PS
(Station name)
→
PTY
(Program type)
→
FREQ
(Frequency)
Note:
RDS may not be available if reception is poor.
Memory presetting
30 FM and 15 AM stations can be preset.
Preparation
Press [RADIO, EXT-IN] to select “FM” or “AM”.
Automatic presetting
1 Press [OK] to select “LOWEST” or “CURRENT” frequency.
2 Press [AUTO PRESET] to start presetting.
To cancel, press [8].
Manual presetting
1 Press [3] or [5] to tune in to the station.
2 Press [PROGRAM].
3 Press the numeric buttons to select a preset number.
Do steps 1 through 3 again to preset more stations.
The new station replaces any station that occupies the same preset
number.
Selecting a preset station
Press the numeric buttons, [2] or [6] (main unit: [2/3] or
[5/6]) to select the preset station.
AM allocation setting (by main unit only)
This system can also receive AM broadcasts allocated in 10 kHz steps.
1 Press [RADIO, EXT-IN] to select “FM” or “AM”.
2 Press and hold [RADIO, EXT-IN].
After a few seconds, the display panel shows the current minimum
radio frequency. Release the button when the minimum frequency
changes.
• To go back to the initial setting, do the above steps again.
• After you change the setting, preset frequencies are erased.
SC-HC15_EP_01en.indd 7 SC-HC15_EP_01en.indd 7 3/11/2011 5:24:21 PM 3/11/2011 5:24:21 PM