Silverline 850W SDS Plus Hammer Drill - Manual (Page 5)

WARNING: Always wear ear protection where the sound level exceeds 85dB(A) and
limit the time of exposure if necessary. If sound levels are uncomfortable, even with ear
protection, stop using the tool immediately and check the ear protection is correctly fitted
and provides the correct level of sound attenuation for the level of sound produced by
your tool.
WARNING: User exposure to tool vibration can result in loss of sense of touch, numbness,
tingling and reduced ability to grip. Long term exposure can lead to a chronic condition. If
necessary, limit the length of time exposed to vibration and use anti-vibration gloves. Do
not operate the tool with hands below a normal comfortable temperature, as vibration will
have a greater effect. Use the figures provided in the specification relating to vibration to
calculate the duration and frequency of operating the tool.
Sound and vibration levels in the specification are determined according to EN60745 or
similar international standards. The figures represent normal use for the tool in normal
working conditions. A poorly maintained, incorrectly assembled, or misused tool, may
produce increased levels of noise and vibration. www.osha.europa.eu provides information
on sound and vibration levels in the workplace that may be useful to domestic users who
use tools for long periods of time.
Carefully read and understand this manual and any label attached to the tool before use.
Keep these instructions with the product for future reference. Ensure all persons who use
this product are fully acquainted with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk factors. Use
with caution. If you are at all unsure of the correct and safe manner in which to use this
tool, do not attempt to use it.
Safety Information
WARNING Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury.
WARNING: This appliance is not intended for use by persons (including children) with
reduced, physical or mental capabilities or lack of experience or knowledge unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children must be supervised to ensure that they do not play
with the appliance.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded) power tool
or battery-operated (cordless) power tool.
Work Area Safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents
b) Do not operate power tools in explosive atmospheres, such as in the presence
of flammable liquids, gases or dust. Power tools create sparks which may ignite
the dust or fumes
c) Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control
Electrical Safety
a) Power tool plugs must match the outlet. Never modify the plug in any way. Do
not use any adapter plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric shock
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded
c) Do not expose power tools to rain or wet conditions. Water entering a power tool
will increase the risk of electric shock
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged or entangled cords increase the risk of electric shock
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of electric
shock
NOTE: The term “residual current device (RCD)” may be replaced by the term
“ground fault circuit interrupter (GFCI)” or “earth leakage circuit breaker (ELCB)”.
Personal Safety
a) Stay alert, watch what you are doing and use common sense when operating a
power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power
tools may result in serious personal injury
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the
tool. Carrying power tools with your finger on the switch or energising power tools
that have the switch on invites accidents
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury
e) Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations
4
GB
Specification
Voltage: .................................................................... 230V~50Hz
Motor: ...................................................................... 850W
No load speed: ......................................................... 800rpm
Safety Clutch (operates at or below): ....................... 56.4Nm
Impact rate: ............................................................. 3200bpm
Impact energy: ......................................................... 1.5J
Max drilling capacity:
-Concrete & stone ................................................... dia 26mm
-Wood ..................................................................... dia 40mm
-Steel ...................................................................... dia 13mm
Fuse rating .............................................................. 13A
Protection class: ......................................................
Ingress protection rating: ......................................... IP20
Power cable length: ................................................. 2M
Power cable type: .................................................... H07RN-F
Weight: .................................................................... 4.7kg
As part of our ongoing product development, specifications of Silverline
products may alter without notice.
Sound and Vibration Information
Weighted vibration (hammer drill):.............24.184m/s 2 (main handle)
14.583m/s 2 (aux. handle)
Weighted vibration (chisel mode):..............20.473m/s 2 (main handle)
14.360m/s 2 (aux. handle)
Uncertainty: ............................................................. 1.5m/s 2
Sound pressure:....................................................... 96.1dB(A)
Sound power: .......................................................... 107.1dB(A)
Uncertainty .............................................................. 3dB(A)
The sound intensity level for the operator may exceed 85dB(A) and sound
protection measures are necessary.
Description of Symbols
The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use.
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction manual
Double insulated for additional protection
Conforms to relevant legislation and safety standards
Environmental Protection
Waste electrical products should not be disposed of with
household waste. Please recycle where facilities exist. Check
with your local authority or retailer for recycling advice
633821_Z1MANPRO1.indd 4 12/08/2013 10:52