Pioneer EFX-1000 - Manual (Page 10)

10
EFFECTS
EFFECTS (Beat Effects)
Beat Effects
1. DELAY effect
Adds delay sound to the original sound.
[BPM mode]
A delay sound is added to the original
sound at the value set with the TIME dial.
÷ The DEPTH dial can be used to adjust
the feedback level. Feedback means to
input the delay sound back into the
delay input. This control allows the
amount of the feedback to be adjusted
(near the [MAX] setting, the sound level
rises).
÷ The CHARACTER dial can be used to
adjust the amount of filter applied to the
feedback sound.
÷ The MIX dial can be used to adjust the
levels of the original and delay sounds.
2. ECHO effect
Adds delay sound to the original sound.
[BPM mode]
A delay sound is added to the original
sound at the value set with the TIME dial.
[RHYTHM mode]
Adds TAP delay sound to the original
sound (Max 8-TAP).
Difference from the DELAY effect:
÷ Even if the BEAT EFFECTS lever switch
is moved from [ON] to [OFF], the
feedback sound or TAP delay sound will
continue.
÷ In the BPM mode, if the DEPTH dial is
set to [MAX] and the BEAT EFFECTS
lever switch is moved from [ON] to
[OFF], a hold-delay effect will be
produced without attenuating the
feedback sound (near the [MAX] setting,
the sound level rises).
In the RHYTHM mode, when the switch
is turned [OFF] the effect will end with
the final TAP delay sound for the
original sound.
[RHYTHM mode]
A delay sound set with the TAP button
(TAP delay sound) is added to the original
sound (Max 8-TAP).
÷ The DEPTH dial can be used to adjust
the TAP delay level (near the [MAX]
setting the sound volume will rise).
÷ The CHARACTER dial can be used to
adjust the amount of filter applied to the
TAP delay sound.
÷ The MIX dial can be used to adjust the
levels of the original and TAP delay
sounds.
3. PITCH ECHO effect
Changes the pitch of the delay sound, and
applies the effect to the original sound.
In the same way as for the ECHO effect, the
effect sound is maintained even if the BEAT
EFFECTS lever switch is set from [ON] to
[OFF].
[BPM mode]
Changes the pitch of the delay sound set
with the TIME dial, and applies the effect to
the original sound.
÷ The DEPTH dial can be used to adjust
the feedback level.
÷ The CHARACTER dial can be used to
adjust the pitch of the delay sound.
÷ The MIX dial can be used to adjust the
levels of the original and pitch echo
sounds.
[RHYTHM mode]
Changes the pitch of the TAP delay sound,
and applies the effect to the original sound
(Max 4-TAP).
÷ The DEPTH dial can be used to adjust
the TAP delay level (near the [MAX]
setting the sound volume will rise
somewhat).
÷ The CHARACTER dial can be used to
adjust the pitch of the TAP delay sound.
÷ The MIX dial can be used to adjust the
levels of the original and pitch echo
sounds.
4. TRANS effect
Cuts the original sound intermittently.
[BPM mode]
Cuts the sound at the interval set by the
TIME dial (cuts latter half of the interval).
÷ The DEPTH dial can be used to adjust
the amount of shift when the sound is
cut.
÷ The CHARACTER dial can be used to
adjust the phase difference between L
and R channels.
÷ The MIX dial can be used to adjust the
levels of the original and trans sounds.
MIN
DEPTH
TIME
DEPTH
TIME
MAX
DEPTH
TIME
Time
Time
Time
CHARACTER
MAX MIN
CHARACTER
TIME
TIME
Time
Time
Time
Time
L-ch
R-ch
L-ch
R-ch
TAP 1 pitch
echo block.
TAP 2 pitch
echo block.
TAP 3 pitch
echo block.
TAP 4 pitch
echo block.
Echo block
BPM mode
TAP 1 echo
block
TAP 8 echo
block
RHYTHM mode
TIME
Feedback
DEPTH
Time
Original
sound
Delay sound
Sound level
Delay block
TAP 0 TAP 1 TAP 2 TAP 3 TAP 4
DEPTH
Time
Original
sound Delay
sound
Sound level
Delay
sound Delay
sound Delay
sound
TAP 1 delay
block
TAP 8 delay
block
Pitch echo
block