Video settings, Additional information 12 – Pioneer VSX-AX2AS-s User Manual
Page 80
Additional information
12
80
En
Video
Settings
Professional Calibration EQ graphical output
Symptom
Remedy
No image is output when an
input is selected.
• Check the video connections of the source component (see page 13).
• For high-definition video (using component video connections), or when digital video conversion is
switched off (in
Setting the AV options
on page 66), you must connect your TV to this receiver using the same
type of video cable as you used to connect your video component.
• Make sure the input assignment is correct for components connected using component or S-video cables
(see
The Input Setup menu
on page 63).
• A separate video source has been selected using
VIDEO SELECT
(see
Watching video and audio sources
independently
on page 68).
• Check the video output settings of the source component.
• Check that the video input you selected on your TV is correct.
• Some components (such as video game units) have resolutions that may not be converted. If adjusting
this receiver’s Resolution setting (in
Setting the AV options
on page 66) and/or the resolution settings on
your component or display doesn’t work, try switching Digital Video Conversion (in
Setting the AV options
on page 66)
OFF
.
Can’t record video.
• Check that the source is not copy-protected.
• The video converter is not available when making recordings. Check that the same type of video cable is
used for connecting both the recorder and the video source (the one you want to record) to this receiver.
Symptom
Remedy
The Auto MCACC Setup
continually shows an error.
• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see also
Problems when using the Auto MCACC Setup
on page 9). If the noise level cannot be kept low enough, you
will have to set up the surround sound manually (page 44).
After using the Auto MCACC
Setup, the speaker size setting is
incorrect.
• There may have been some low frequency noise in the room from an air-conditioner, motor, etc. Switch
off all other appliances in the room and use Auto MCACC Setup again.
• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some cases.
Change the speaker setting manually in
Speaker Setting
on page 45, and use the
ALL (Keep SPsetting)
option for the
Auto Mode
in
Automatic MCACC (Expert)
on page 35 if this is a recurring problem.
Can’t adjust the Fine Speaker
Distance setting (page 39)
properly.
• Check that the speakers are all in phase (make sure the positive (
+
) and negative (
–
) terminals are
matched up properly).
The display shows
KEY LOCK
ON
when you try to make
settings.
• With the receiver in standby, press
STANDBY/ON
while holding down the
MULTI-ROOM&SOURCE
CONTROL
button to disable the key lock.
Most recent settings have been
erased.
• The power cord was disconnected from the wall while adjusting this setting.
Symptom
Remedy
The EQ response displayed in the
graphical output following
calibration does not appear
entirely flat.
• There are cases where the graph does not appear flat (even when selecting
ALL CH ADJUST
in the Auto
MCACC Setup) due to adjustments made to compensate for room characteristics to achieve optimal sound.
• Areas of the graph may appear identical (before and after) when there is little or no adjustment needed.
• The graph may appear to have shifted vertically when comparing before and after measurements.
EQ adjustments made using the
Manual MCACC setup
on
page 38 do not appear to change
the graphical output.
• Despite level adjustments being made, the filters used for analysis may not display these adjustments in
the graphical output. However, these adjustments are taken this into account by the filters dedicated to
overall system calibration.
Lower frequency response
curves do not seem to have been
calibrated for
SMALL
speakers.
• Low frequencies used in bass management (the subwoofer channel) will not change for speakers that
have been specified as
SMALL
in the configuration, or do not output these frequencies.
• Calibration is performed, but due to your speakers’ low frequency limitations, no measurable sound is
output for display.
Graphical output data seems to
have disappeared.
• If the power is switched off, the measurement data for graphical output to a PC is cleared.
VSX_AX4ASi.book.fm 80 ページ ２００６年６月８日 木曜日 午後１２時２３分