Bunn H5M - Manual (Page 4)

4
ELECTRICAL REQUIREMENTS
CAUTION - The dispenser must be disconnected from the power source until specified in Initial Set-Up.
The H5M dispenser requires 2-wire, grounded service rated 120, 208, or 240 volts ac, 20 amp, single phase.
The H5MA, 230V-CE dispenser requires 2-wire, grounded service rated 230 volts ac, 40 amp, single phase, 50/
60Hz
. (Refer to the dispenser’s dataplate for exact voltage requirement.)
Electrical Hook-Up
CAUTION – Improper electrical installation will damage electronic components.
1. An electrician must provide electrical service as specified.
2. Using a voltmeter, check the voltage and color coding of each conductor at
the electrical source.
3. Remove the upper and lower rear panels. Turn the knob of the thermostat to
the “OFF” position (fully counterclockwise).
4. Install a strain relief and the proper electrical wiring to the terminal block.
5. Connect the dispenser to the power source and verify the voltage at the termi-
nal block before proceeding. Reinstall both rear panels.
6. If plumbing is to be hooked-up later be sure the dispenser is disconnected from
the power source. If Plumbing has been hooked-up, the dispenser is ready for
Initial Set-Up .
PLUMBING REQUIREMENTS
This dispenser must be connected to a COLD WATER system with operating pressure between 20 and 90 psi (138
and 620 kPa)from a
1 ⁄
2
" or larger supply line. A shut-off valve should be installed in the line before the dispenser.
Install a regulator in the line when pressure is greater than 90 psi (620 kPa) to reduce it to 50 psi (345 kPa). The
water inlet fitting is
1 ⁄
4
" flare.
NOTE - Bunn-O-Matic recommends 1 ⁄
4
" copper tubing for installations of less than 25 feet and 3 ⁄
8
" for more than
25 feet from the 1 ⁄
2
" water supply line. At least 18 inches of an FDA approved flexible beverage tubing, such as
reinforced braided polyethylene or silicone, before the dispenser will facilitate movement to clean the countertop.
It can be purchased direct from Bunn-O-Matic (part number 00326-0000). Bunn-O-Matic does not recommend
the use of a saddle valve to install the dispenser. The size and shape of the hole made in the supply line by this type
of device may restrict water flow.
208 or 240V.A.C.
L2 RED
L1 BLACK
120V.A.C. NEUTRAL
WHITE
L1 BLACK
This equipment must be installed to comply with the Basic Plumbing Code of the Building Officials
and Code Administrators International, Inc. (BOCA) and the Food Service Sanitation Manual of the
Food and Drug Administration (FDA).
P1770
Plumbing Hook-Up
1. Flush the water line and securely attach it to the flare fitting on
the rear of the dispenser.
2. Turn-on the water supply.
CON
NECT FROM POWER SOURCE BEFORE REMOVING!
O N
OFF
Fill water tank before turning -on thermostat or connecting appliance
to power source.
Do not use near combustibles.
Follow national/local electrical codes.
Electrically ground the chassis.
Use only on a properly protected
circuit capable of the rated load.
FAILURE TO COMPLY RISKS EQUIPMENT
DAMAGE, FIRE, OR SHOCK HAZARD
RE AD TH E E NTIR
E O PER
AT IN G M AN UA L
IN CLU DING
TH E LIM
IT O F W
AR RA NTY
A ND
LIAB
ILITY B
EFO
RE BU
YIN G O R U SIN G TH
IS PR
ODU
CT
TH IS A
PPLIA
NC E IS H
EA TED W HENE
VE R
CO NN EC TED TO A PO W ER SO
URCE
00831.0000A 5/88 © 1988 BUNN-O-MATIC CORPORATION
W
ARNING
!
This equipment is to be in
st l
comply with the Basic Pl
m
the Building O
ffici
Administrators
Int
and the F
ood
of the
Fo
10267 071900