Carlin 102CRD-99FRD-100CRD - Manual (Page 2)

Model 99FRD, 100CRD & 102CRD oil burners — Instruction manual
Carlin part number MN99102 Rev. 10/21/10
– 2 –
PLEASE read this fi rst . . .
Special attention fl ags
Please pay particular attention to the following when you see them through-
out this manual.
Notifi es you of hazards that WILL cause severe personal injury,
death or substantial property damage.
Notifi es you of hazards that CAN cause severe personal injury,
death or substantial property damage.
Notifi es you of hazards that WILL or CAN cause minor personal
injury or property damage.
Notifi es you of special instructions on installation, operation or
maintenance that are important, but are not normally related
to injury or property damage hazards.
General information
Burner applications
Follow all instructions in this manual, the primary control data sheet and
the appliance manual. Verify the burner is correct for the appliance being
used and for all applicable codes/standards.
Damage or shortage claims
The consignee of the shipment must fi le damage or shortage claims im-
mediately against the transportation company.
When calling or writing about the burner . . .
Please provide us with the UL serial number and burner model number
to assist us in locating information. This information can be helpful when
troubleshooting or obtaining replacement parts.
Follow the guidelines below to avoid potential severe
personal injury, death or substantial property damage.
Installer/service technician . . .
• Read all instructions before proceeding. Perform all procedures,
and in the order given to avoid potential of severe personal injury,
death or substantial property damage.
• Before leaving the site after startup or service, review the User’s
information page with the user. Make the user aware of all potential
hazards and perform the training outlined below.
Train the user . . .
• To properly operate the burner/appliance per this manual and the
appliance instructions see User’s information.
• To keep this manual at or near the burner/appliance for ready ac-
cess by the user and service technician.
• To contact the service technician or oil dealer if he encounters
problems with the burner/appliance.
• To keep the appliance space free of fl ammable liquids or vapors
and other combustible materials.
• Do not use laundry products, paints, varnishes or other chemicals
in the room occupied by the burner/appliance.
• To contact the service technician at least annually for startup and
burner/appliance service.
When servicing the burner . . .
• Disconnect electrical supply to burner before attempting to service
to avoid electrical shock or possible injury from moving parts.
• Burner and appliance components can be extremely hot. Allow
all parts to cool before attempting to handle or service to avoid
potential of severe burns.
Should overheating occur:
(1) shut off the oil supply to the burner.
(2) do not shut off the control switch to the circulator or
blower.
Certifi cation
99FRD, 100CRD, and 102CRD burners are U.L. listed for the U.S. and
Canada, certifi ed to comply with ANSI/UL 296, for use with #1 or #2 heating
oil (per standard ASTM D396).
Burner labels list compliance, when required, with special local, state or
provincial approvals.
United States installations
Burner/appliance installations in the United States must comply with the
latest editions of NFPA 31 (Standard for the Installation of Oil-Burning
Equipment), ANSI/NFPA 70 (National Electrical Code), and all applicable
local codes.
Canadian installations
Burner/appliance installations in Canada must comply with the latest editions
of CSA B139 (Installation Code for Oil Burning Equipment), CSA standard
C22, Part 1 (Canadian Electrical Code), and all applicable local codes.
Codes and standards
Install this burner in accordance with all local codes and
authorities having jurisdiction. Regulations of these authori-
ties take precedence over the general instructions provided
in this manual.