Document Outline

• Cover Page
• Title Page
• Trademarks
• Disclaimer
• Copyright
• Declaration Of Conformity
• Warranty
• Table Of Contents
• Chapter 1 Introduction and Specifications
  • 1.1 Introduction
    • 1.1.1 IQM-233 Card Features
    • 1.1.2 IQM-233 Standard Software Features
    • 1.1.3 IQS-233 Codeposition Software Features
    • 1.1.4 Related Operating Manuals
  • 1.2 Instrument Safety
    • 1.2.1 Definition of Notes, Cautions and Warnings
    • 1.2.2 General Safety Information
  • 1.3 How To Contact INFICON
    • 1.3.1 Returning Your IQM-233 Card to INFICON
  • 1.4 IQM-233 Specifications
    • 1.4.1 Measurement
    • 1.4.2 Source Outputs
    • 1.4.3 Computer Requirements
    • 1.4.4 General Specifications
    • 1.4.5 Operating Environment
    • 1.4.6 Storage Temperature
    • 1.4.7 Warm Up Period
    • 1.4.8 Size
      • 1.4.8.1 IQM-233 Card (without bracket) H x L
      • 1.4.8.2 IQM-233 Card (standard) H x L x W
      • 1.4.8.3 IQM-233 Card (Small Form Factor) H x L x W
    • 1.4.9 Connector Clearances
    • 1.4.10 Weight
  • 1.5 Unpacking and Inspection
  • 1.6 Configurations and Accessories
    • 1.6.1 IQM-233 Card Configurations
    • 1.6.2 Accessories
      • 1.6.2.1 Software (Optional)
      • 1.6.2.2 Cables and Oscillator Kits
      • 1.6.2.3 Crystal Sensors
• Chapter 2 Installation and Interfaces
  • 2.1 Installation
    • 2.1.1 Installation Requirements
      • 2.1.1.1 Computer Requirements
      • 2.1.1.2 Software Requirements
      • 2.1.1.3 Installation Precautions
      • 2.1.1.4 Parts Requirements
      • 2.1.1.5 Ground Requirements
        • 2.1.1.5.1 Earth Ground
    • 2.1.2 Installation Procedure
      • 2.1.2.1 IQM-233 Card Installation
        • 2.1.2.1.1 IQM-233 Card Installation Troubleshooting
      • 2.1.2.2 Sensor Connections
        • 2.1.2.2.1 Sensor Connection Troubleshooting
      • 2.1.2.3 Source Output Cable and Connection
      • 2.1.2.4 Source Output Configuration and Verification
      • 2.1.2.5 Digital I/O Connections
• Chapter 3 IQM-233 Standard Software
  • 3.1 Introduction
  • 3.2 How To Install IQM-233 Standard Software
    • 3.2.1 DLL Installation
      • 3.2.1.1 DLL Installation Troubleshooting
    • 3.2.2 IQM-233 Standard Software Installation
    • 3.2.3 IQM-233 Standard Software Update
  • 3.3 How To Use IQM-233 Standard Software
    • 3.3.1 Starting the Software
      • 3.3.1.1 Starting the Software in Windows XP or Windows 7
      • 3.3.1.2 Starting the Software in Windows 8
    • 3.3.2 IQM-233 Standard Window Introduction
    • 3.3.3 Software Configuration
      • 3.3.3.1 Setup
        • 3.3.3.1.1 Log
        • 3.3.3.1.2 General
        • 3.3.3.1.3 Sensor
        • 3.3.3.1.4 Source
      • 3.3.3.2 Map Sensor
      • 3.3.3.3 Source Control
      • 3.3.3.4 File
    • 3.3.4 IQM-233 Standard Window Description
      • 3.3.4.1 Sensor Information Pane Readouts
      • 3.3.4.2 Source Information Pane Readouts
      • 3.3.4.3 Global Operating Functions
      • 3.3.4.4 Source Control Operating Functions
      • 3.3.4.5 Simulate Mode
      • 3.3.4.6 About IQM-233 Standard Window
      • 3.3.4.7 Current Configuration File
      • 3.3.4.8 Exit Window
• Chapter 4 Remote Communications
  • 4.1 Introduction
  • 4.2 DLL Functions
  • 4.3 LabVIEW VI Sample
    • 4.3.1 Getting Started With The LabVIEW VI Sample
• Chapter 5 Troubleshooting and Maintenance
  • 5.1 Troubleshooting Guide
  • 5.2 Maintenance
  • 5.3 Spare Parts
• Chapter 6 Calibration Procedures
  • 6.1 Importance of Density, Tooling and Z-Ratio
  • 6.2 Determining Density
  • 6.3 Determining Tooling
  • 6.4 Determining Z-Ratio
  • 6.5 Tuning the Control Loop
    • 6.5.1 Identifying a Fast or Slow Source
    • 6.5.2 Loop Tuning Procedure
• Chapter 7 Measurement Theory
  • 7.1 Basics
    • 7.1.1 Monitor Crystals
    • 7.1.2 Period Measurement Technique
    • 7.1.3 Z-Match Technique
• Appendix A Material Table
  • A.1 Introduction