Weidmuller WI-MOD-945-E: 900Mhz Wireless Ethernet & Device Server v2.16 - Manual (Page 3)

Page 3 www.weidmuller.com Rev 2.16
FCC Notice:
This device complies with Part 15.247 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference and
2. This device must accept any interference received, including interference that may cause undesired operation.
This device must be operated as supplied by Weidmuller. Any changes or modifications made to the device without the
written consent of Weidmuller
may void the user’s authority to operate the device.
End user products that have this device embedded must be installed by experienced radio and antenna personnel, or
supplied with non-standard antenna connectors, and antennas available from vendors specified by WEIDMULLER.
Please contact WEIDMULLER for end user antenna and connector recommendations.
In accordance with 47 CFR Part 15 Subpart C Section 15.203 only the following antenna/coax cable kits combinations
can be used.
Manufacturer Model Number Coax Kit Net
WEIDMULLER WI-ANT-DPL-DG00-1 Includes 1m Cellfoil -2dB Loss
WEIDMULLER WI-ANT-DPL-0-16 Includes 5m Cellfoil Unity Gain
WEIDMULLER WI-ANT-900MHZ-5DB OMNI NF WI-ACC-TYP400-40FT-NM-NM 1.8dB Gain
WEIDMULLER WI-ANT-900MHZ-5DB OMNI NF WI-ACC-TYP400-75FT-NM-NM -1.2dB Loss
WEIDMULLER WI-ANT-900MHZ-7DB OMNI NF WI-ACC-TYP400-40FT-NM-NM 4.8dB Gain
WEIDMULLER WI-ANT-900MHZ-7DB OMNI NF WI-ACC-TYP400-75FT-NM-NM 1.8dB Gain
WEIDMULLER WI-ANT-900MHZ-6.5DB YAGI NF WI-ACC-TYP400-10FT-NM-NM 6.8dB Gain
WEIDMULLER WI-ANT-900MHZ-6.5DB YAGI NF WI-ACC-TYP400-75FT-NM-NM 3.8dB Gain

Part 15 – This device has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part15 of the FCC rules (Code of Federal Regulations 47CFR Part 15). Operation is subject to the condition that
this device does not cause harmful interference.

Notice any changes or modifications not expressly approved by WEIDMULLER could void the user’s authority to
operate this equipment.
This Device should only be connected to PCs that are covered by either FCC DoC or are FCC certified.
Safety Notices:
Exposure to RF energy is an important safety consideration. The FCC has adopted a safety standard for human exposure
to radio frequency electromagnetic energy emitted by FCC regulated equipment as a result of its actions in Docket 93-62
and OET Bulletin 65 Edition 97-01.
UL Notice:
1. The Wireless Ethernet module is to be installed by trained personnel / licensed electricians only and installation
must be carried out in accordance with the instructions listed in the Installation Guide and applicable local
regulatory codes.
2. The units are intended for Restricted Access Locations.
3. The Wireless Ethernet module is intended to be installed in a final enclosure, rated IP54, before use outdoors.
4. The Equipment shall be powered using an external Listed Power Supply with LPS outputs or a Class 2 Power
Supply.
5. The Wireless Ethernet module must be properly grounded for surge protection before use.
6. If installed in a hazardous environment coaxial cable shall be installed in a metallic conduit