Blomberg WNF 7300 WE20 - Manual (Page 12)

12 EN
active, previously selected programme will continue
running.
To activate the Child Lock:
Press and hold 1 st and 2 nd Auxiliary Function buttons for
3 seconds. The lights on the 1 st and 2 nd Auxiliary Function
buttons will flash, and "C03", "C02", "C01" will appear on the
display respectively while you keep the buttons pressed for
3 seconds. Then, "Con" will appear on the display indicating
that the Child Lock is activated. If you press any button or turn
the Programme Selection knob when the Child Lock is active,
same phrase will appear on the display. The lights on the 1st
and 2nd auxiliary function buttons that are used to deactivate
the Child Lock will blink 3 times.
To deactivate the Child Lock:
Press and hold 1 st and 2 nd auxiliary function buttons for 3
seconds while any programme is running. The lights on the
1 st and 2 nd Auxiliary Function buttons will flash, and "C03",
"C02", "C01" will appear on the display respectively while
you keep the buttons pressed for 3 seconds. Then, "COFF"
will appear on the display indicating that the Child Lock is
deactivated.
C In addition to the method above, to deactivate the Child
Lock, switch the Programme Selection knob to On /
Off position when no programme is running, and select
another programme.
C Child Lock is not deactivated after power failures or
when the machine is unplugged.
C If you switch off the machine by pressing the On / Off
button when the Child Lock is active and the machine is
running, then the child lock will be deactivated.
Progress of programme
Progress of a running programme can be followed from the
Programme Follow-up indicator. At the beginning of every
programme step, the relevant indicator light will turn on and
light of the completed step will turn off.
You can change the auxiliary functions, speed and
temperature settings without stopping the programme flow
while the programme is running. To do this, the change
you are going to make must be in a step after the running
programme step. If the change is not compatible, relevant
lights will flash for 3 times.
C If the machine does not pass to the spinning step,
Rinse Hold function might be active or the automatic
unbalanced load detection system might be activated
due to the unbalanced distribution of the laundry in the
machine.
Loading door lock
There is a locking system on the loading door of the machine
that prevents opening of the door in cases when the water
level is unsuitable.
Loading door light will start flashing when the machine
is switched to Pause mode. Machine checks the level of
the water inside. If the level is suitable, Loading Door light
illuminates steadily within 1-2 minutes and the loading door
can be opened.
If the level is unsuitable, Loading Door light turns off and the
loading door cannot be opened. If you are obliged to open
the Loading Door while the Loading Door light is off, you
have to cancel the current programme; see "Canceling the
programme".
Changing the selections after
programme has started
Switching the machine to pause mode
Press the Start / Pause button to switch the machine to pause
mode while a programme is running. The light of the step
which the machine is in starts flashing in the Programme
Follow-up indicator to show that the machine has been
switched to the pause mode.
Also, when the loading door is ready to be opened, Loading
Door light will also illuminate continuously in addition to the
programme step light.
Changing the speed and temperature settings for
auxiliary functions
Depending on the step the programme has reached, you
may cancel or activate the auxiliary functions; see, "Auxiliary
function selection".
You may also change the speed and temperature settings;
see, "Spin speed selection" and "Temperature selection".
C If no change is allowed, the relevant light will flash for 3
times.
Adding or taking out laundry
Press the Start / Pause button to switch the machine to
pause mode. The programme follow-up light of the relevant
step during which the machine was switched into the pause
mode will flash. Wait until the Loading Door can be opened.
Open the Loading Door and add or take out the laundry.
Close the Loading Door. Make changes in auxiliary functions,
temperature and speed settings if necessary. Press Start /
Pause button to start the machine.
C The loading door will not open if the water temperature
in the machine is high or the water level is above the
door opening.
Canceling the programme
To cancel the programme, turn the Programme Selection
knob to select another programme. Previous programme will
be canceled. End / Cancel light will flash continuously to notify
that the programme has been canceled.
Pump function is activated for 1-2 minutes regardless of the
programme step, and whether there is water in the machine
or not. After this period, your machine will be ready to start
with the first step of the new programme.
C Depending on the step where the programme was
canceled in, you may have to put detergent and softener
again for the programme you have selected anew.
C If you want to open the loading door after you have
cancelled the programme but it is not possible to open
the loading door since the water level in the machine
is above the loading door opening, then turn the
Programme Selection knob to Pump+Spin programme
and discharge the water in the machine.
End of programme
“End” appears on the display at the end of the programme.
Wait until the loading door light illuminates steadily. Press On
/ Off button to switch off the machine. Take out your laundry
and close the loading door. Your machine is ready for the next
washing cycle.