Reloop WAVE 8 - Manual (Page 6)

6
ENGLIS
CH
Congratulations on purchasing your Reloop Wave 5 / Wave 8 active monitors. Thank you for placing your trust in our technology. Before operating
this equipment we ask you to carefully study and observe all instructions.
Please remove your Reloop Wave 5 / Wave 8 active monitors from its packaging. Check before initial operation to make sure that the device has
not been visibly damaged during transport. If you detect any damage to the power cable or the casing, do not operate the device. Contact your
specialised dealer.
SAfeTy InSTRUcTIonS
cAUTIon!
Please exercise particular caution when handling 230 V power voltage. This voltage rating may lead to a critical electrical shock! Any damage
caused by the non-observance of this operation manual excludes any warranty claims. The manufacturer is not liable for any damage to pro-
perty or for personal injury caused by improper handling or non-observance of the safety instructions.
- This device left the works in a perfect condition. To maintain this condition and to ensure a risk-free operation the user must observe the
safety instructions and warnings contained in this operation manual.
- For reasons of safety and certification (CE) the unauthorised conversion and/or modification of the device is prohibited. Please note that in
the event of damage caused by the manual modification to this device any warranty claims are excluded.
- The inside of the device does not contain any parts which require maintenance, with the exception of wear parts that can be exchanged from
the outside. Qualified staff must carry out maintenance, otherwise the warranty does not apply!
- Ensure that the power will only be supplied after the device has been fully set up. Always plug in the mains plug last. Ensure that the mains
switch is in the „OFF“ position when connecting the device to power.
- Only use cables that comply with regulations. Observe that all jacks and bushes are tightened and correctly hooked up. Refer to your dealer
if you have any questions.
-
Ensure that when setting up the product the mains cable is not squashed or damaged by sharp edges.
- Prevent the mains cable from coming into contact with other cables! Exercise great care when handling mains cables and connections. Never
touch these parts with wet hands!
- Be sure to connect the product exclusively to 230 V, 50 Hz A/C! Make sure to put the voltage selector switch -17- is in the correct, country-
specific position (230V, 50 Hz or 115V, 60 Hz). For Germany: 230V, 50 Hz. The manufacturer is not liable for damage resulting from an
incorrect voltage. In such a case any warranty claims are excluded.
-
The fuse must be exchanged exclusively against fuses of the same class, with the same trigger features and nominal current rating.
- Connect the power cable exclusively to appropriate shock-proof outlets. The only supply point to be used is a supply outlet in accordance
with specifications of the public supply network.
-
Disconnect the device from the supply outlet when not in use and before cleaning! Be sure to hold the mains plug by the body. Never pull
the mains cord!
-
Position the device on a horizontal and stable low-flame base. When experiencing feedback, direct the radiation field of your
loudspeakers away from the device.
-
Avoid any concussions or violent impact when installing or operating the device.
-
When selecting the location of installation make sure that the device is not exposed to excessive heat, humidity, and dust. Be sure that no
cables lie around openly. You will endanger your own safety and that of others!
-
Do not rest any containers filled with liquid that could easily spill onto the device or in its immediate vicinity. If, however, fluids should
access the inside of the device, immediately disconnect the mains plug. Have the device checked by a qualified service technician before
re-use. Damage caused by fluids inside the device is excluded from the warranty.
-
Do not operate the device under extremely hot (in excess of 35° C) or extremely cold (below 5° C) conditions. Keep the device away from
direct exposure to the sun and heat sources such as radiators, ovens, etc. (even during transport in a closed vehicle). Never cover the
cooling fan or vents. Always ensure sufficient ventilation.
- The device must not be operated after being taken from a cold environment into a warm environment. The condensation caused hereby may
destroy your device. Do not switch on or operate the device until it has reached ambient temperature!
- Controls and switches should never be treated with spray-on cleaning agents and lubricants. This device should only be cleaned with a damp
cloth. Never use solvents or cleaning fluids with a petroleum base for cleaning.
- When relocating the device should be transported in its original packaging.
-
When starting operation the cross-faders and volume controls of your amplifier must be set to minimum level. Bring the loudspeaker
switches into the „OFF“ position. Wait between 8 to 10 seconds before increasing the volume to avoid shot noise created by transient effect,
which could cause damage to loudspeakers and the diplexer.
-
Devices supplied by voltage should not be left in the hands of children. Please exercise particular care when in the presence of children.
-
At commercial facilities the regulations for the prevention of accidents as stipulated by the association of professional associations must be
observed.
-
At schools, training facilities, hobby and self-help workshops the operation of the device must be monitored with responsibility by trained staff.
-
Keep this operation manual in a safe place for later reference in the event of questions or problems.