Reloop WAVE 8 - Manual (Page 9)

9
oPeRATIon SPeAKeRS
1. Set volume control to minimum level
Before switching on the device, turn the volume dials -1- & -14- to minimum position (dials all the way to the left).
2. Power ON
After all connections have been completed activate the device with the ON/OFF Switch -16-. The Power Status LED -4- and the Input Status
LED -5-will be lit.
3. Volume control
Adjust the volume with the corresponding dial -1-.
cAUTIon!
Before switching on the power all volume controls of your final amplifier must be set to a minimum. Before increasing the volume wait 8 to 10
seconds to avoid damage to the loudspeakers.
oPeRATIon exTeRnAl WAVe conTRol
1. Volume control
Adjust the volume with the corresponding dial -14-.
cAUTIon!
Before switching on the power all volume controls of your final amplifier must be set to a minimum. Before increasing the volume wait 8 to 10
seconds to avoid damage to the loudspeakers.
2. Stand By / Mute
With this button it is possible to select two functions:
a) Mute
By presing this button -2- shortly, the device will switch to mute mode. The Input Status LED -5-, the Power Status LED -4- and the Reloop
sign on the device‘s upper side will start blinking. By pressing again, mute mode will be deactivated again.
b) Stand By
Press the button -2- for approximately 2 seconds; the device will switch to stand by. The Input Status LED -5-, the Power Status LED -4- and
the Reloop sign on the device‘s upper side will be dimmed. By pressing again for approximately 2 seconds, stand by mode will be deactivated
again.
3. Input Select Button
By pressing this button -3- it is possible to select the input source (XLR, jack or RCA). The corresponding LED -5- will be lit.
SoUnd conTRol
1. Use the HF Trim Switch -9- to lower or raise the high frequencies by - 2 dB or by +2 dB respectively, besides the normal position (0 dB).
This is very useful when using your passive monitors in larger rooms for example.
2. Use the Acoustic Space Switch -10- to adjust your speakers according to the set-up in the room (0 dB, -2 dB, -4 dB) since the acoustic pressure
in the low-frequency range is increased from the reflection of adjacent surfaces. Distorted reproduction caused by positioning in corners or
near walls can be copensated this way.
3. Use the LF Cutoff Switch -11- to either fade the low-range frequency below 60 Hz, or 80 Hz or to bring it in the “Flat” position. This is very
useful when, for example, you intend to simulate the sound on a less bass-heavy speaker system or you are using an additional subwoofer or
want to suppress rumble noise.
TechnIcAl InfoRMATIon
Global Distribution GmbH did not test the following manufacturers’ specification for plausibility and accuracy:
Reloop Wave 5:
-
Output capacity : RMS 50W, max. 100W
- Input sensitivity/impedance : +1.3dBu/20kohm (XLR & 6.3mm jack), -4.1dBu/20kohm (RCA)
- Tweeter : 2.5cm (1“) dome tweeter
- Woofer : 13cm (5“) paper cone woofer
- Maximum acoustic pressure : 102dB rated, 87dB RMS
- Frequency range : 32Hz - 20kHz (+/-3dB)
- Inputs : 1x XLR (symmetrical), 1x 6.3mm jack (symmetrical), 1x RCA (asymmetrical), 1x mini-DIN (controller)
- Dimensions : (w)185 x (h)320 x (d)230 mm (incl. cooling fin)
- Weight : 6.0 kg (per speaker)
Reloop Wave 8:
-
Output capacity : RMS 70W, max. 140W
- Input sensitivity/impedance : +0.5dBu/20kohm (XLR & 6.3mm jack), -5.5dBu/20kohm (RCA)
- Tweeter : 2.5cm (1“) dome tweeter
- Woofer : 20cm (8“) paper cone woofer
- Maximum acoustic pressure : 105dB rated, 90dB RMS
- Frequency range : 20Hz - 20kHz (+/-3dB)
- Inputs : 1x XLR (symmetrical), 1x 6.3mm jack (symmetrical), 1x RCA (asymmetrical), 1x mini-DIN (controller)
- Dimensions : (w)250 x (h)388 x (d)310 mm (incl. cooling fin)
- Weight : 9.5 kg (per speaker)
Subject to alterations!
Illustrations similar to original product!
Misprints excepted!
ReloopTrademark
Global Distribution GmbH, Schuckertstr. 28, 48153 Münster, Germany, Fax +49.251.60 99 368
ENGLIS
CH