Sound Devices 552 - Manual (Page 48)

552 User Guide and Technical Information
44
v. 1.4 Features and specifications are subject to change. Visit www.sounddevices.com for the latest documentation.
Function Key Sequence Action
Save User
Setup to Inter-
nal Memory
+
Hold PFL 2 and press the Stop button
Saves User Settings to the internal memory of the 552.
Load User Setup
from Internal
Memory
+
Hold PFL 2 and press the Headphone Controller
Recalls User Settings from the internal memory of the 552.
Load Factory
Settings + +
Hold PFL 4 and press the Headphone Controller and the Battery Check button
Restores all Setup Menu parameters to Factory Default.
Connector Pin Assignments
Connector Pin Assignments Notes
XLR F
Analog Inputs 1-5
1 – ground
2 – signal (+)
3 – signal (-)
3.3k ohm input impedance, Mic- and Line-level Transform-
er Balanced. For unbalanced, pin 1 and pin 3 tied together
= ground, pin 2 = positive.
TA3M
Direct Outputs 1-4
1 – ground
2 – signal (+)
3 – signal (-)
Active balanced, output level is selectable in Setup Menu
as Line, -10, or Mic level. For unbalanced, pin 1 = ground,
pin 2 = positive, pin 3 = float (no connect). Mates with
Switchcraft TA3F-type connector.
3 .5 mm
Mono Mic Output
tip – signal L and R
sleeve – signal ground
Mates with 3.5 mm TS jack. Designed to interconnect
Wireless IFB Transmitters and Transcription Recorders,
signal is unbalanced.
3 .5 mm
Tape Output
tip – signal L
ring – signal R
sleeve – signal ground
Mates with 3.5 mm TRS jack. Signal is unbalanced.
XLR M
Master Outputs/
AES A,B Outputs
1 – ground
2 – signal (+)
3 – signal (-)
Transformer balanced, Output Level is selectable using
switch between Mic, -10 dB, or Line-level. For unbalanced,
pin 1 and pin 3 tied together = ground, pin 2 = positive.
Balanced AES3 Out A,B on XLR connectors, 110 ohm,
2 V p-p, AES3 and S/PDIF compatible with RCA adaptor.
3 .5 mm
RTN B
tip – signal L
ring – signal R
sleeve – signal ground
Mates with 3.5 mm TRS jack. Signal is unbalanced.
10-Pin Hirose F
Master Output / RTN A
Input
1 – L (+) output
2 – L (–) output
3 – R (+) output
4 – R (–) output
5 – R (+) return A
6 – n/c
7 – L (+) return A
8 – n/c
9 – ground
10 – ground
Mates with Hirose RM15TPD-10P(71) connector.
Outputs are Transformer Balanced, output level is select-
able using switch between Line, -10, or Mic level. For
unbalanced connections XLR connectors should be wired,
pin 1 and pin 3 tied together = ground, pin 2 = positive.
Balanced AES3 Out A,B on 10-Pin connector, 110 ohm, 2
V p-p, AES3 and S/PDIF compatible with RCA adaptor.
TA3M
RTN B Input or TC Input
1 – ground
2 – left signal
3 – right signal
(For TC, 1 and 3 - ground,
pin 2 - hot +)
Unbalanced stereo input. Used for either Return B audio
input or time code input for the recorder. When time code
is enabled, use RTN B 3.5 mm for RTN B audio input.
Mates with Switchcraft TA3F-type connector.
TA3M
L and R Outputs
1 – ground
2 – signal (+)
3 – signal (-)
Active balanced, output level is selectable in Setup Menu
as Line, -10, or Mic level. For unbalanced, pin 1 = ground,
pin 2 = positive, pin 3 = float (no connect). Mates with
Switchcraft TA3F-type connector.
TA3M
Tape Output
1 – ground
2 – Left Signal
3 – Right Signal
Unbalanced stereo output. Mates with Switchcraft TA3F-
type connector.