Cobra Electronics MICROTALK CXR925C - Manual (Page 7)

Customer Assistance Warranty Introduction Operation
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
Using your Radio
and Mode Functions
Scrolling through Mode Functions
•
By scrolling through the Mode Functions, you will be able to
select or turn on/off preferred features of your microTALK ® radio. When
scrolling through the Mode Functions, your radio features
will be displayed in the following order:
Set CTCSS Privacy Codes
Set DCS Privacy Codes
Set NOAA All Hazards Radio Channel
Set VOX On/Off
Set VOX Sensitivity Level
Set Memory Locations
Set Channel Scan
Set CTCSS Privacy Code Scan
Set DCS Privacy Code Scan
Set Memory Location Scan
Set VibrAlert ® and/or Call Alert
Set Call Alert Tone Signal
Set Roger Beep On/Off
Set Keystroke Tones On/Off
Scroll through the mode functions using the Mode button. Each press and
release of the Mode button will advance to the next mode function. Press
the Talk button at any point to return the radio to Standby mode.
Operation
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
LI 7300
Mode Button
Intro Operation Customer
Assistance
Warranty
Notice
Main Icons
Secondary Icons
microTalk ® Range
•
Your range will vary depending on terrain and conditions.
In flat, open country your radio will
operate at maximum range.
Buildings and foliage in the path of the
signal can reduce the range of the radio.
Dense foliage and hilly terrain will
further reduce the range of the radio.
On FRS channels 8 through 14, your radio
automatically switches to low power, which
will limit the range the radio can communicate.
Remember, you can achieve maximum
range by using maximum range extender.
See page 6 for details.
Maximum Range
Reduced Range
Reduced Range
To play back an incoming transmission:
1. Check that the Rew icon is illuminated. If it is not,
turn on Rewind-Say-Again.
2. Press the Rewind button.
The most recent call recorded will play, then second
most recent, and so on. Play back can be stopped at
any time by pressing the Rew or Talk button.
To record an outgoing message:
1. Check that the Rew icon is illuminated. If it is not,
turn on Rewind-Say-Again.
2. While no message is being received, press and
hold the Hi-Lo Power button until the Rew icon
blinks.
3. Press and hold the Talk button and begin recording your message.
The display will show a 20-second countdown and
the Rew icon will stop blinking.
4. Release the Talk button at the end of your message to end recording. The
Rew icon will remain illuminated.
If attempting a long recording, two beeps will sound at the end of
20 seconds, then recording will stop and the first 20 seconds of your
message will be saved.
To review your recorded outgoing message:
1. Check that the Rew icon is illuminated. If it is not, turn on
Rewind-Say-Again.
2. Press the Rewind button.
The message will play through the speaker and the display will show
a 20-second countdown, but the message will not be transmitted.
The radio will return to standby at the end of the message.
To send (transmit) your message:
1. Check that the Rew icon is illuminated. If the icon is not illuminated,
turn on Rewind-Say-Again.
2. Press and hold the Talk button, then press the Rewind button.
3. Release the Talk button when you hear the beginning of the message
from the speaker.
The message will continue to transmit and play to the end, then the
radio will return to standby. Transmission can be stopped at any time by
pressing the Rew or Talk button.
LI 7300
Rewind Button
Rewind Icon
Talk Button
8 English 9 Nothing Comes Close to a Cobra ®
CXR925C_ENG_MANL.indd 8-9 12/15/09 2:19 PM