Dell 5210n Mono Laser Printer User Manual
Page 70
Cancel not available
Wait for the message to clear.
Cancelling
Wait for the message to clear.
Change <src> <Custom Type Name>
l
Press the Select button
if you have changed the media.
l
Select Use current to print on media currently in the printer.
l
Cancel the current job.
Change <src> <Custom String>
Change <src> <size>
Change <src> <type> <size>
Check duplex connection
l
Turn the printer off and back on. If the error recurs, turn the printer off, unplug the power cord from the wall
outlet, and then remove the duplex unit. Reattach the duplex unit, connect the power cord to a properly
grounded outlet, and restart the printer. For more information, see
Installing a Duplex Unit
.
If the error recurs, turn the printer off, unplug the power cord from the wall outlet, and then remove the
specified device, and call for service.
l
Press the Select button
to clear the message and print without using the device.
Check tray <x> connection
l
Turn the printer off and back on. If the error recurs, turn the printer off, unplug the power cord from the wall
outlet, and then remove the specified tray. Reattach the tray, connect the power cord to a properly grounded
outlet, and restart the printer. For more information, see
Installing a 250-Sheet or 500-Sheet Drawer
.
If the error recurs, turn the printer off, unplug the power cord from the wall outlet, and then remove the
specified device, and call for service.
l
Press the Select button
to clear the message and print without using the device.
Clearing job accounting statistics
Wait for the message to clear.
Close Door or Insert Cartridge
l
Close the upper front door.
l
Install the toner cartridge.
Copies
Enter the desired number of copies.
Defragmenting Flash
DO NOT POWER OFF
Wait for the message to clear.
NOTE:
Do not turn the printer off while this message is displayed.
Delete
l
Press the Select button
to delete the specified job.
l
Press Stop to cancel the operation.
Delete all
l
Press the Select button
to delete all confidential jobs.
l
Press Stop to cancel the operation.
Delete all confidential jobs
l
Press the Select button
to delete all held jobs.
l
Press Stop to cancel the operation.
Deleting
Wait for the message to clear.
Disabling DLEs
Wait for the message to clear.
Disabling Menus
Wait for the message to clear.
NOTE:
While the menus are disabled, you cannot change the printer settings from the operator panel.
Enabling Menus
Wait for the message to clear.
Enter PIN
Enter the PIN you identified in the driver when you sent the confidential job to the printer.
Enter PIN to lock
Enter the correct pin number to lock the operator panel and prevent menu changes.
Flushing buffer
Wait for the message to clear.
Formatting Flash
DO NOT POWER OFF
Wait for the message to clear.
NOTE:
Do not turn the printer off while this message is displayed.
Hex Trace
The printer is in Hex Trace mode.
Insert Tray <x>
Insert the specified tray into the printer.
Install bin <x>
l
Turn the printer off, unplug the power cord from the wall outlet, install the specified bin, connect the power
cord to a properly grounded outlet, and then restart the printer. For more information, see
Installing a 250-
Sheet or 500-Sheet Drawer
.
l
Cancel the current job.
Install duplex
l
Turn the printer off, unplug the power cord from the wall outlet, install the duplex unit, connect the power
cord to a properly grounded outlet, and then restart the printer. For more information, see
Installing a Duplex
Unit
.
l
Cancel the current job.
Install envelope feeder
l
Turn the printer off, install the envelope feeder, and restart the printer. For more information, see
Installing
an Envelope Feeder
.
l
Cancel the current job.
Install tray <x>
l
Turn the printer off, unplug the power cord from the wall outlet, install the specified tray, reconnect the power
cord to a properly grounded outlet, and then restart the printer. For more information, see
Installing a 250-
Sheet or 500-Sheet Drawer
.
l
Cancel the current job.