To protect a minidisc against accidental erasure, Notes on recording, If "protected" appears in the display – Sony MDS-S35 User Manual
Page 7: If "track" flashes in the display, When "toc" flashes in the display, If "din unlock" appears in the display, Recording on mds
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Recording on MDs
To protect a MiniDisc against accidental erasure
lo nic'iko \l impossible record on an MO, slide the tab in the
direction i>l arrow , opening; the ->lot. I o alii,n\’ recording, liosi-
the slot.
Rear of the disc
Record-protect tab
'Q' You can start recording from the middle of a recorded
track in Step 5
Press I>DD (or ►) to start playback, press 1>0D (or
I I )
where vcm want tc^ start recording, and then do the
procedure starting from Step 6 on page 6, I lowewr, you
will not be able to record from the middle ot a recorded
track it "Id^CiRAM" or "SHUFFLE” appears in the
display.
Notes on Recording
If "Protected" appears in the display
The MD is record-protected. Close theAlot to record on the
disc (see "To pnTect a N4iniDisc against accidental erasure" on
this page).
• When recording from source connected through 1 l\'F
(ANAI.tx:) l\ with INPUT at ANALOG, and "LiA'F.L-
S^’\C" does not light up (sot- "Marking Track Numbers
While Keci>rding'' on page “-Ь i>r when ivcordiiig fri>m I )/\ !
connected thix'ugh DIGITAL IN with INPU i at DIGH AL:
The source will be recorded as a single track, ^'ou can di\’idt.'
the track afterwards using the Di\ ide l-uncticai (see
"Dix'iding Rect)i'ded Tracks" (>n page LS) or mark track
numbers during recording by using the Track Marking
I'unction on page
It "LFVI-.L SYNC" appears in the display, the deck
automaticalK' marks track numbers when recording analog
source or digital recording of DAT (see "Marking track
numbers automatically" on page ‘-h.
If "TRACK" flashes in the display
The deck is recording twer an existing track. "TRACK" lights
continuously when the recorder reaches the end ol the
preyiously recorded portion.
When "TOC" flashes in the display
The deck is currently updating the Table of Contents O'OC).
Do move the recorder or pull out the AC power cord.
Changes to an MD made through recording are sawed only
vyhen you update the TOC by ejecting the MD or changing the
deck to standby by pressing POWER.
The MD deck uses the SCMS (Serial Copy Management
System on page 27)
MDs recorded through DIGITAL IN cannot be copied onto
other MDs through DIGITAL IN.
If "Din Unlock" appears in the display
• The programme source is not connected to DIGITAL IN
even though you've selected DIGITAL in Step 4 or the
sampling frequency of the programme source does not
match that of the MD deck (44.1 kl Iz). To continue, connect
the programme source through DIGITAL IN or select
ANALOG in Step 4 to record through LINE (ANALOCA IN.
• The digital signal has been interrupted (stopped) while you
were recording. To continue recording, restart the digital
programme source. To stop recording, press ■ on the MD
deck.
Depending on source being recorded, track numbers are
marked in following ways:
• When recording from a CD or MD w ith INPUT at DIGITAL
and the source connected thixfiigh DlCilTAL IN;
The deck automaticalK' marks track numbers in the same
sequence ,is the original. If, however, a track is repeated tw'o
or more times (e.g. b\ single-track repeal play) or two or
mori' tracks with the same track number (e.g. from different
MDs or CDs) are played, the track or tracks are recorded as
part ot a single, continuous track with a single track number.
It the soLirci' is an .MI), track numbers may not be marked for
tracks of k‘ss th.m 4 st.'eoiKls.