2 cp6003-ra board-specific information, Cp6003-ra board-specific information - 4, Introduction cp6003-ra/rc – Kontron CP6003-RC User Manual
Page 24
Introduction
CP6003-RA/RC
Page 1 - 4
ID 1046-3890, Rev. 1.0
P R E L I M I N A R Y
1.2
CP6003-RA Board-Specific Information
The CP6003-RA is a rugged air-cooled CompactPCI single-board computer with front I/O. It is
based on the 2
nd
generation Intel® Core™ i7 processor and specifically designed for use in
highly integrated platforms with solid mechanical interfacing for a wide range of industrial
environment applications.
Some of the CP6003-RA's outstanding features are:
•
Support for the following 2
nd
generation processors:
•
Quad-core Intel® Core™ i7-2715QE (SV), 2.1 GHz, 6 MB L3 cache
•
Dual-core Intel® Core™ i7-2655LE (LV), 2.2 GHz, 4 MB L3 cache
•
Intel® QM67 Express chipset
•
Up to 16 GB, dual-channel, soldered DDR3 SDRAM memory with ECC running at 1333 MHz
•
Integrated 3D high-performance graphics controller with up to four high-resolution graphics
interfaces (VGA / DP / 2 x HDMI/DVI)
•
64-bit/66 MHz PCI or PCI-X CompactPCI interface (PICMG 2.0)
•
One PMC slot with PCI functionality and rear I/O support; 64-bit/66 MHz PCI interface or
64-bit/133 MHz PCI-X interface
•
One XMC slot utilizing a x8 lane PCI Express 2.0 interconnection
•
Five Gigabit Ethernet interfaces:
•
Two Gigabit Ethernet interfaces switchable between front I/O and rear I/O
•
Two Gigabit Ethernet interfaces on rear I/O (PICMG 2.16)
•
One Gigabit Ethernet interface on front I/O
•
Two Gigabit Ethernet (GbE) controllers:
•
One Intel® 82579LM Gigabit Ethernet controller connected to one GbE port on the front panel
•
One Intel® 82580EB Quad Gigabit Ethernet controller connected to two GbE ports on
the front panel and two GbE ports on the rear I/O
•
Five Serial ATA interfaces with SATA RAID 0/1/5/10 support:
•
One onboard SATA 6 Gb/s interface for the Serial ATA Flash module
•
Four SATA 3 Gb/s interfaces on the rear I/O
•
Six USB ports:
•
Two USB 2.0 ports on the front panel
•
Four USB 2.0 ports on the rear I/O
•
Two COM ports:
•
One RS-232 COM port either on the front panel or on the rear I/O (COMA)
•
One RS-422/RS-232 COM port on the rear I/O (COMB)
•
TCG 1.2 compliant Trusted Platform Module (TPM), on request
•
Two SPI boot flashes:
•
One standard SPI boot flash
•
One recovery SPI boot flash
•
Four general purpose inputs (GPI) and four general purpose outputs (GPO) on rear I/O
•
Watchdog timer
•
Battery-backed real-time clock
•
Three onboard DIP switches for board configuration
•
Supports PICMG Packet Switching Backplane Specification 2.16
•
IPMI support
•
4HP, 6U CompactPCI
•
Passive heat sink solution for forced airflow cooling
•
Rear I/O on J3, J4 and J5
•
Hot swap capability: as system controller or as peripheral device
•
AMI Aptio®, a uEFI-compliant platform firmware