Replacing an ac power supply, Follow these steps to replace an ac power supply, Step 1 – Cisco 10005 User Manual
Page 10: Step 2, Caution, Adding or replacing an ac power supply, Power fault
Adding or Replacing an AC Power Supply
10
Cisco 10005 ESR AC Power Supply Installation
78-12652-01
Replacing an AC Power Supply
Warning
Never install an AC power module and a DC power module in the
same chassis.
Follow these steps to replace an AC power supply:
Step 1
Put on an antistatic wrist or ankle strap. Attach the strap to the ESD grounding
jack on the front of the chassis or to the bare metal surface of the chassis.
Step 2
If your system is configured with redundant power supplies, set only the power
switch of the power supply you are replacing to the standby position (
).
Caution
Do not power off both AC power supplies in a redundant system, or the system
shuts down and all data traffic stops. Power off only the AC power supply you
are replacing.
Figure 4
Setting AC Power Switch to the Standby Position
53629
CRITICAL
ALARM
MINOR
ALARM
MAJOR
ALARM
60 VDC
1A MAX
NO
CO
NC
A+
A-
B+
B-
NO
CO
NC
NO
CO
NC
EXT
CLOCK
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
POWER
FAULT
POWER
FAULT
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
CRITICAL
ALARM
MINOR
ALARM
MAJOR
ALARM
60 VDC
1A MAX
NO
CO
NC
A+
A-
B+
B-
NO
CO
NC
NO
CO
NC
EXT
CLOCK
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
THIS UNIT HAS M
ORE THAN ONE PO
WER
SUPPL
Y CORD. DISCONNECT
TWO (2)
POWER SUPPL
Y CORDS BEFO
RE
SERVICING T
O AVOID ELECTRIC SHOCK.
CAUTION
POWER
FAULT
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
RX
TX
THIS UNIT HAS M
ORE THAN
ONE PO
WER
SUPPL
Y CORD. DISCO
NNECT TW
O (2)
POWER SUPPL
Y CORDS BEFORE
SERVICING T
O AVOID ELECTRIC SHO
CK.
CAUTION
POWER
FAULT
100-240V
50/60 HZ
15-7A
100-240V
50/60 HZ
15-7A
POWER
FAULT