Clarion VRX633R - Manual (Page 13)

VRX633R
17
English
Owner
’s manual
Basic Operations
When the panel is closed:
Each time you press the Z-EHCR button 9 , the
tone effect changes in the following order:
“Z-EHCR 1” ➜ “Z-EHCR 2” ➜ “Z-EHCR 3” ➜
“Z-EHCR OFF” ➜ “Z-EHCR 1”...
When the panel is open:
1. Press the A-M button ™ to change into the
AUDIO-MODE display.
2. Operate the JOYSTICK § upward or down-
ward to select “Z-EHCR”. Press the ENT at
the center of the JOYSTICK
§ to change into
the Z-enhancer selecting display.
3. Operate the JOYSTICK § upward or down-
ward to select out of:
“TYPE 1” (Z-Enhancer 1) “TYPE 2” (Z-En-
hancer 2) “TYPE 3” (Z-Enhancer 3)
“OFF” (Z-Enhancer off),
and press the ENT at the center of the JOY-
STICK
§ to set a desired Z-enhancer.
4. When the setting is finished, operate the JOY-
STICK § rightward or leftward to move the
cursor to the “MENU”. Then press the ENT at
the center of the JOYSTICK
§ to return to
the AUDIO-MODE display.
∗
To return from the AUDIO-MODE display to the
STANDARD display, press the A-M button
™
once again.
Adjusting the Z-enhancer
Note:
• This function is enabled only when the panel is
open.
1. Press the A-M button ™ to change into the
AUDIO-MODE display.
2. Operate the JOYSTICK § upward or downward
to select “Z-EH LVL” level. Press the ENT at the
center of the JOYSTICK
§ to change into the
Z-enhancer adjusting display.
3. Operate the JOYSTICK § upward or down-
ward to adjust the Z-enhancer level.
∗
When Z-Enhancer 1 is selected, you can adjust
the bass in the range of ±2.
∗
When Z-Enhancer 2 is selected, you can adjust
the treble in the range of ±2.
∗
When Z-Enhancer 3 is selected, you can adjust
the bass and treble in the range of ±2.
4. When the adjustment is finished, operate the
JOYSTICK § rightward or leftward to move
the cursor to “MENU”. Then press the ENT at
the center of the JOYSTICK
§ to return to
the AUDIO-MODE display.
Adjusting the bass and treble
Notes:
• This function is enabled only when the panel is
open.
• This function can be adjusted only when the Z-
enhancer is OFF.
1. Press the A-M button ™ to change into the
AUDIO-MODE display.
2. Operate the JOYSTICK § upward or down-
ward to select “BAS/TRE”. Then press the
ENT at the center of the JOYSTICK
§ to
change into the BASS/TREBLE adjusting dis-
play.
3. Operate the JOYSTICK § rightward or left-
ward to adjust the “BASS” or “TREBLE”.
4. Operate the JOYSTICK § upward or down-
ward to adjust a level (adjustment range: from
-6 to 6).
5. When the adjustment is finished, operate the
JOYSTICK § rightward or leftward to move
the cursor to “MENU”. Then press the ENT at
the center of the JOYSTICK
§ to return to
the AUDIO-MODE display.
Adjusting the balance and fader
Note:
• This function is enabled only when the panel is
open.
1. Press the A-M button ™ to change into the
AUDIO-MODE display.
2. Operate the JOYSTICK § upward or down-
ward to select “BAL/FAD”. Then press the
ENT at the center of the JOYSTICK
§ to
change into the BAL/FAD adjusting display.
3. Operate the JOYSTICK § rightward or left-
ward to select “BALANCE” or “FADER”.
4. Operate the JOYSTICK § upward or down-
ward to make an adjustment.
Adjusting range of the balance: L13 to R13
Adjusting range of the fader: front 12 / rear 12
5. When the adjustment is finished, operate the
JOYSTICK § rightward or leftward to move
the cursor to “MENU”. Then press the ENT at
the center of the JOYSTICK
§ to return to
the AUDIO-MODE display.