Cybex TOPAZ - Manual (Page 19)

11
11. USING THE HaRNESS SYSTEm
a) To fasten the harness system insert left and right side fasteners into the central
harness buckle.
b) To tighten the belts pull the strap on the front of the central harness buckle.
c) To release the belt system press the release button located on the seat in front
of the belt lock while pulling at the shoulder belts.
d) To release the fasteners squeeze the grooves on left and right side of the
central harness buckle.
e) Adjust the length of the crotch strap with the corresponding slider.
WaRNING: aLWaYS USE THE CRoTCH STRaP IN ComBINaTIoN
WITH THE WaIST BELT.
12. aDJUSTING THE HaRNESS SYSTEm FoR NEWBoRNS
a) Release the loops at the end of the shoulder straps from the triangle in the belt
system, situated at the bottom of the backrest under the seat cover.
b) Completely pull the shoulder straps out of the holes in the backrest.
c) Feed the shoulder straps through the two bottom holes. Make sure to feed the
straps back through the holes in the backrest mechanism and re-attach them
to the triangle.
d) To adjust the length of the shoulder straps to newborns please attach the inner
loop of the shoulder strap ends to the triangular ring. switch back to the upper
holes as soon as the shoulder straps do no longer fit over the child´s shoulders.
13. REmoVING THE HEaDHUGGER aND SHoULDER PaDS (ToPaZ oNLY)
Remove the headhugger as soon as the headhugger does no longer fit over the
child´s shoulders.
a) Remove the velcros of the headhugger on the top leh and right side on the
back of the seat cover.
b) Release the loops at the end of the shoulder straps from the triangle in the belt
system, situated at the bottom of the backrest under the seat cover.
c) Completely pull the shoulder straps out of the holes in the backrest.
d) Pull the shoulder straps through the shoulder pads and the headhugger. Make
sure to feed the straps back through the holes in the backrest mechanism and
attach them to the triangle. You can use the headhugger and the shoulder
pads separately.
14. REmoVING THE SEaTCoVER
a) Slightly fold the stroller to reduce tension.
b) Remove the canopy from the stroller, if attached.
c) Take the seat cover’s hooks (3) off the frame on left and right side
d) Open the press buttons (4) of the straps connected to the seat side panels
and the basket rear tube.
e) Open the flaps (5) which are fixed with velcro over the tubes, one on each
side.
f) Feed the strap with the slider (6) of the central harness buckle through the hole
in the seat fabric.
g) Feed the loops on the end of the shoulder straps through the triangle in the
backrest (7).
h) Feed the shoulder straps through the holes in the seat fabric (8).
i) Open the press buttons which are on the left and the right side from the seat
on the bottom from the fabric.
j) Pull the seat cover over the belt shifting button on the seat.
k) Slide the fabrics from the seat base tubes.
l) Reverse this procedure to refit the seat cover and the harness. Make sure that
the seat tubes slide back into the pockets inside the seat cover.
15. RECLINING THE LEG REST
a) Press the leg rest on both front edges and push down.
b) Simply lift the leg rest to put it back to the starting position.
16. RECLINING THE SEaT
a) Pull the recline lever at the back of the seat in order to recline the backrest to
the 4 different positions.
b) To raise lift the complete backrest up to required position.
17. CaRRYING THE STRoLLER
–
Pull the flexible carring handle on right rear tube and lift the stroller.
18. aTTaCHING THE RaINCoVER (oPTIoNaL)
a) Extend the rain cover over the stroller like shown in the image
b) To fit the rain cover fasten the velcro strips around the frame at the top and
bottom on both sides of the buggy.
19. WaRRaNTY
The following warranty applies solely in the country where this product was
initially sold by a retailer to a customer. The warranty covers all manufacturing
and material defects, existing and appearing, at the date of purchase or
appearing within a term of two (2) years from the date of purchase from the
retailer who initially sold the product to a consumer (manufacturer’s warranty).
in the event that a manufacturing or material defect should appear, we will
– at our own discretion – either repair the product free of charge or replace it
with a new product. To obtain such warranty it is required to take or ship the
product to the retailer, who initially sold this product to a customer and to
submit an original proof of purchase (sales receipt or invoice) that contains
the date of purchase, the name of the retailer and the type designation of this
product. This warranty shall not apply in the event that this product is taken or
shipped to the manufacturer or any other person other than the retailer who
initially sold this product to a consumer. please check the product with respect
to completeness and manufacturing or material defects immediately at the
date of purchase or, in the event that the product was purchased in distance
selling, immediately after receipt. in case of a defect stop using the product