Document Outline

• Inventory
• Safety
  • Do not install the UPS in direct sunlight, in excessive heat, humidity, or in contact with fluids.
  • Do not connect a laser printer or hair dryer to the unit.
  • Ensure that the connected equipment does not exceed the maximum load.
• Overview
  • Mute
  • Ethernet ports
  • Power On/Off
  • Master outlet
  • Display/Menu
  • Circuit breaker
  • Display interface
  • Battery back-up outlets
  • Surge protection outlets
  • Controlled outlets
  • Data port
• Connect the battery
  • Charge the battery for at least 16 hours before use.
• Connect the equipment
  • 1 . Connect equipment to the Battery Backup and Surge Protection outlets. When the Back-UPS is re...
  • 2 . Use the AC power cord to connect the Back-UPS directly to a utility power outlet.
  • 3 . Connect a router or cable modem to the corresponding ports.
  • 1 . Connect the supplied USB software interface cable to the data port, and the other end to a co...
  • 2 . Go to www.apc.com/tools/download.
  • 3 . Select PowerChute Personal Edition. Then select the appropriate operating system and follow t...
• Operation
  • On Line—The UPS is supplying utility power to connected equipment
  • Power-Saving—Master and controlled outlets are enabled, saving power when the master device goes ...
  • Load Capacity—The load is indicated by the number of sections illuminated, one to five. If the lo...
  • Battery Charge—The battery charge level is indicated by the number of sections illuminated. When ...
  • Overload—The power demand from the load has exceeded the capacity of the Back-UPS.
  • Event—An event has occurred and the unit needs attention.
  • Automatic Voltage Regulation—The unit is compensating for extremely low input voltage, but is not...
  • In—Input voltage. Out—Output voltage.
  • System Faults—The system has a fault. The fault number will illuminate on the display interface. ...
  • Mute—The audible alarm has been turned off.
  • Replace Battery—The battery is not connected or is nearing the end of its useful life. Replace th...
  • On Battery—The unit is supplying battery backup power to the connected equipment, it will beep fo...
  • Press Display to scroll through the display screens.
    • Input Voltage
    • Estimated runtime in minutes
    • Counter
    • Power Event Counter
    • Estimated run time
    • Output Voltage
    • Load in Watts
    • Input Voltage
    • Load in %
    • Load in Watts
    • Output Voltage
    • Load in %
    • Output Frequency
    • Output Frequency
    • AVR: The Automatic Voltage Regulation (AVR) feature will compensate for excessively low input vol...
• Configuration
  • To conserve electricity, configure the Back-UPS to recognize a Master device, such as a desktop c...
  • Enable the Power-Saving feature
    • Press and hold Mute and Display simultaneously for two seconds. The unit will beep to indicate th...
  • Disable the Power-Saving feature.
    • Press and hold Mute and Display simultaneously for two seconds. The unit will beep to indicate th...
  • Setting the threshold
    • The amount of power used by a device in Sleep or Standby mode varies between devices. It may be n...
    • 1 . Ensure a master device is connected to the Master outlet. Put that device into Sleep or Stand...
    • 2 . Press Display and Mute simultaneously and hold for six seconds, until the leaf icon flashes t...
    • 3 . The Back-UPS unit will now recognize the threshold level of the Master device and save it as ...
    • When unit power is On, the LCD may remain illuminated or be darkened for energy savings.
    • 1 . Full Time LCD Mode: Press and hold DISPLAY for two seconds. The LCD will illuminate and the u...
    • 2 . Power-Saving Mode: Press and hold DISPLAY for two seconds. The LCD will darken and the unit w...
    • Adjust the sensitivity of the UPS to control when it will switch to battery power; the higher the...
    • 1 . Ensure the unit is connected to utility power, but is OFF.
    • 2 . Press and hold the Power button for six seconds. The Load Capacity bar will flash on and off,...
    • 3 . Press Power again to rotate through the menu options. Stop at selected sensitivity. The unit ...
      • Low sensitivity
      • Medium sensitivity
      • High sensitivity
• 78-144 Vac
• 88-141 Vac
• 88-137 Vac
  • Input voltage is extremely low or high. (Not recommended for computer loads.)
  • The Back-UPS frequently switches to battery power.
  • The connected equipment is sensitive to voltage fluctuations.
  • Warnings and System Faults
    • Press Display to scroll through the display screens.
      • ON LINE overload condition, indicated by the illuminated ON LINE icon, and the flashing overload ...
      • In ON LINE mode, and there is a bad battery, indicated by the flashing icon.
      • Backup battery (ON BATT) overload condition. This is indicated by the flashing overload icon.
      • The battery charge is low, and the Battery Charge indicator bar is flashing.
    • The unit will display the fault messages. Contact APC Technical Support for additional support.
      • • F01 - On-Battery Overload
      • • F02 - On-Battery Output Short
      • • F03 - On-Battery Xcap Overload
      • • F04 - Clamp Short
      • • F05 - Charge Fault
      • • F06 - Relay Welding
      • • F07 - Temperature
      • • F08 - Fan Fault
      • • F09 - Internal Fault
  • Function Button Quick-Reference
    • Power
    • Power On
• 0.2
• Off
  • Press Power to start receiving input utility power. If A/C input power is not available, the unit...
  • Power Off
• 2
• On
  • The unit is not receiving input utility power, but is providing surge protection.
  • Display
  • Status Inquiry
• 0.2
• On
  • Verify the status or condition of the unit. The LCD will illuminate for 60 seconds.
  • Full-Time/Power- Saving mode
• 2
• On
  • The LCD will illuminate and the unit will beep to confirm the Full-Time mode. The LCD will darken...
  • Mute
  • Event Specific
• 0.2
• On
  • Disable any audible alarms caused by an event.
  • General Status Enable/ Disable
• 2
• On
  • Enable or disable the audible alarms. The Mute icon will illuminate and the unit will beep one ti...
  • Sensitivity
• 6
• Off
  • The Load Capacity icon will blink, indicating that the unit is in programming mode. Use the Power...
  • Master/Controlled outlet Enable/Disable
• 2
• On
  • The leaf icon will darken indicating that the Master Outlet feature is disabled or illuminate to ...
  • Master/Enable Threshold Calibration
• 6
• On
  • While calibrating the threshold setting, the device connected to the Master Outlet should be turn...
  • Self-Test (manual)
• 6
• On
  • The UPS will perform a test of the internal battery. Note: This will happen automatically when th...
  • Event Reset
• 0.2
• On
  • When the Event screen is visible, press and hold Display, then press power, to clear the utility ...
  • Fault Reset
• 2
• Fault
  • After a fault has been identified, press Power to remove the visual indication and return to stan...
  • Troubleshooting
    • Battery Backup outlets may be fully or improperly loaded.
  • Specifications
    • General
    • Topology
    • Line-Interactive
    • Input
    • Rated input voltage
    • 120 Vac
    • Phase
    • Single phase 2+ ground
    • Frequency
    • 50/60 Hz (autosensing)
    • Input voltage range
    • (on AVR operation)
    • Default setting: 88 V-141 V
    • Lower Limit Voltage Range: 78 V- 144 V
    • Upper Limit Voltage Range: 88 V- 137 V
    • Power cable length
    • 6 ft
    • Input plug type
    • NEMA5-15
    • Output
    • Output plug type
    • NEMA5-15R
    • Output outlet
    • Back-up outlets (3)
    • Surge outlets (3)
    • Maximum load
    • 700 VA/420 W
    • Output voltage
    • 115 Vac + 8%
    • Frequency
    • 50/60 Hz +1
    • On-battery waveform
    • Stepped sine wave
    • Transfer time
    • Maximum 8 ms
    • Surge Protection/Noise
    • Surge protection
    • Yes
    • Noise filter
    • Yes
    • Data line protection
    • ADSL, ISDN, 10/100Base-T
    • Interface
    • Interface
    • USB v1.1
    • If the Back-UPS arrived damaged, notify the carrier.
    • If the Back-UPS requires service, do not return it to the dealer.
    • 1 . Consult the Troubleshooting section to eliminate common problems.
    • 2 . If the problem persists, go to http://www.apc.com/support/.
    • 3 . If the problem still persists, contact APC Technical Support.