Panasonic CF-48 - Manual (Page 26)

Reinstalling Software
After the reinstallation procedure completes, the follow­
ing message will appear on the display.
(WJ n3ф^В^9l3|№
All data on the whole HDD has been restored to the factory default.
After removing floppy disk and the Product Recovery CD-ROM,
restart the computer and set up Windows again.
Remove the Product Recovery CD-ROM and FIRST AID
FD, then restart the computer by pressing ( Ctrl ) +
CM)+CDiD ■
AVürin3ö;^2^0.0.01
Windows2000 install wizard will start after reboot.
Restore process will execute more after WindowsIOOO install wizard.
Restart the computer after removing floppy disk and CD.
Remove the Product Recovery CD-ROM, then restart the
computer by pressing rctrn + CSD+CBiD
(WJndo^NiTA
Restart the computer several times for Windows Prepara­
tion.
If the message “Preinstallation completed successfully.
Press any key to shut down/reboot.” is displayed, press
any key.
11 When the message [Press <F2> to enter SETUP] is dis­
played, press (1^2 ) and then run the Setup Utility.
If the password has been set, enter the Supervisor Pass­
word.
12 Press
At the confirmation message, select [Yes] and press
C Enter]. (The Setup Utility settings will return to their
default values. Even the security settings with the excep­
tion of the password(s) will return to their default val­
ues.)
Change the settings where necessary.
13 Press ( F10 ).
At the confirmation message, select [Yes] and press
(Enter).
14 Perform the setup procedure for Windows by following
the instructions on the screen.
^ page 11
Described on the
right
tWJndGM98lMW.in30№
AWjndc^Nirâ
CWJ n do^^2Wl
<When the Backup Disk has been created page 13>
Set the Backup Disk and select [OK].
(If the Backup Disk has not been created, select [Can­
cel].)
(Windcivi^NiTM
Setup Windows after reinstalling
(T) The Software License Agreement will be displayed.
After reading the agreement, select [I Agree].
note ).
• If [I Disagree] is selected, the Windows setup
will be aborted.
• Moving the cursor (i^) or clicking buttons can
be performed with the touch pad.
Select [Next].
Input your name and organization, then select [Next].
(It is possible to omit the organization item.)
Input the Product ID written down in the column
“Customer’s record” (Q^age 2) then select [Next],
To move the cursor to a particular item, press
CM3 or click the desired box.
Input your computer name and select [Next],
@ Input an Administrator password and select [Next].
---------------------------------- ^
j Remember this password! If the password is for-
' gotten, Windows NT cannot be operated.
V
( t ) Select [Next].
®
Select [Do not connect this computer to a network at
this time], then select [Next].
(Settings can be made for a network even after Win­
dows starts up. In this case, be sure to read [When
Adding New Software or Hardware Components] in
the Reference Manual [Technical Information].)
• When establishing settings for a network:
The settings will vary for different network envi­
ronments depending on the network system being
used. For more details, ask your system adminis­
trator or the person in charge of the network. Fol­
low the on-screen instructions.
<Modcl with both an internal modem and internal
LAN port>
The driver for the internal LAN port is in
[c:\util\drivers\clan]. Be sure to select [Intel(R) PRO
Adapter].
X note )
It takes several minutes for the necessary files to
be copied. If the computer enters the ECO mode,
the power to the LCD is automatically turned off.
In this case, press a key unrelated to the direct
triggering of a selection, likeCShift).
26