Yamaha HTR-5860 - Manual (Page 3)

IMPORTANT SAFETY INSTRUCTIONS
d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to its normal
operation,
e) If the product has been dropped or damaged in any
way, and
f) When the product exhibits a distinct change in perfor­
mance - this indicates a need for service.
20 Replacement Parts - When replacement parts are required,
be sure the service technician has used replacement parts
specified by lire manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
hazards.
21 Safety Clieck - Upon completion of any service or repairs to
this product, ask the service technician to perform safety
checks to determine iinit the product is in proper operating
condition,
22 Wall or Ceiling Mounting - Tlie unit should he mounted
to a w'all or ceiling only its recommended hy the
manufacturer.
23 Heat - The product should be situated aw'ay from heat
sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's
attention to Article 820-40 of the NEC that provides
guidelines for proper grounding and. in particular, specifies
that the cable ground shall be connected to the grounditig
system of the building, as close to the point of ctible entry as
practical.
24 Outdoor Antetma Groundiitg - If an outside antetma or
cable system is connected to the product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Article 8IOof the National Electrical Code. ANSI/NFP
a ' t O,
provides information with regard to proper grounding of the
mast and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, size of grounding conductors,
location of antenna discharge tniit, connection to grounding
electrodes, ;ind requirements for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING
ANTENNA
DISCHARGE UNIT
(NEC SECTION ft10-20)
GROUNDING CONDUCTORS
(NEC SECTION B10-2Î)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 2S0. PARTH)
FCC INFORMATION (for US customers)
IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when histalled as hidicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Ytimaha may void your authority, granted by the FCC, to
use the product.
IMPORTANT : When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with Ibis product MU.ST
be used. Follow all installation inslructions. Failure to
follow' instruclions could void your FCC authorization to
use this product, in the USA.
NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class "B” digital devices. Compliance w'ith these
rcqtiirernents provides a reasonable level of assurance that
your use of this product in a residential environment w'ill
not result in htiraifnl interference with other electronic
devices.
This equipment geiierates/uses radio frequencies and, if
not installed and used according to the inslructions found
in the users manual, may cause interference harmful to the
operation of other electronic devices.
Compliance with FCC regulations docs not guarantee that
interference will not occur in all installations. If this
product is found to be the source of interference, which
can be determined by turning the unit "OFF" and "ON",
please try to eliminate the problem hy using one of the
following measures:
Relocate either this product or the device that is being
affected hy the interference.
Utilize pow'er outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/rcoricnt
the antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Oraugelhorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY lo those products
distributed hy Yamaha Corporation of America or its
subsidiaries.