Insert editing, Preparation – Panasonic NV-FS1 User Manual
Page 33
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
INSERT EDITING
When this type of editing is done, the picture and the sound
are recorded on the tape as shown below. However, if no
new sound is input, only the “normal” original sound
remains on the tape because the original Hi-Fi sound will
always be erased during insert editing.
Video and Audio Track Recording Pattern
“Normal” Audio
JTrack Original
Sound
K
Video Tracks
(Inserted Picture)
Hi-Fi Audio Tracks
(Inserted Sound)
□
O O O O
§D|-J
Cl
g ; - — - = i
I i l o
Insert Editing Indicator
©
VTAv'TV AUCMO SELECT
AUDIO OUBINSERT
REC*
MEMOflf
RESET
an
REW/Q"-
à
------ PLAT-------- ©/FF
czm
STOP
PAUSE/STILL
cc
SEARCH
©
CZD
— INDEX
O
<K
____ >_____ ' >>
"1
□
1
5
T~l
1
^
© o
n
Preparation
•Select the video playback channel on the TV set.
•Insert a video cassette with the erasure prevention tab
intact.
•When performing insert editing from another VTR, set the
Image Selector to “EDIT".
•Set the Input Signal Selector according to the type of
Insert Editing to be performed.
'‘LINE/AUDIO”: When inserting picture and sound from
equipment connected to the Video Input
Socket and the Audio Input Sockets on
the rear of this VTR.
“TUNER":
When inserting scenes from a TV pro
gramme.
“S-VIDEO”:
When inserting picture and sound from
equipment connected to the S-Video
Input Socket and the Audio Input Sockets
on the rear of this VTR.
O Press the Play Button.
^ Set the S-VHS Selector according to the S-VHS
Indicator.
When the S-VHS Indicator is
lit......................................................... Set to “AUTO”.
not lit .................................................. Set to “OFF".
© Locate the tape position where you want the insert
editing to end, and press the Pause/Still Button at that
position to put the VTR into the still playback mode.
O Press the Reset Button to reset the Tape Counter to
“
0
:
00
.
00
”.
© Press the Memory/Search Button so that the Memory
Indicator “M” mark will appear.
^ Keep the Rewind/Revlew Button pressed for reverse
playback at high speed and release the button when
the scene, where the insert editing is to start, has been
passed.
O Press the Pause/Still Button to start playback, and
locate the point where the insert editing is to start.
O Press the Pause/Still Button at the insert editing start
point to put the VTR into the still playback mode.
^ Press the Insert Editing Button.
(The Insert Editing Indicator lights up.)
© When the source VTR, from which the picture is to be
inserted, is ready, press the Pause/Still Button to start
the insert editing.
•The insert editing will end at the point where the Tape
Counter becomes “0:00.00", and the editing VTR will
stop in the still playback mode.
•It is not necessary to operate the Tape Speed
Selector.
•The picture quality of an inserted part is always
somewhat inferior to that of the original.
•Avoid performing insert editing repeatedly on the
same part of the tape because the picture quality of
that part becomes inferior.
•Do not press the Memory/Search Button during
insert editing. If it is pressed, the Memory Indication
“M” will disappear, and the insert editing will not
end automatically at the preset editing end point.
•If the Stop Button is pressed on the editing VTR to
finish the insert editing, noise bars will later be
visible at that position of the tape.
♦The inserted picture may contain slight colour noise
or colours may be unstable.