Power, Troubleshooting guide – Panasonic DVD-RV21 User Manual
Page 30
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Troubleshooting guide
Before requesting service, make the beiow checks, if you are in doubt about some of the check points, or if the remedies indicated in the chart
do not solve the problem, contact below.
In the U.S.A., contact the Panasonic Customer Call Center at 1-800-211-7262, or e-mail [email protected], or
web site (http:/A№ww.panasonic.com).
In Canada, contact Panasonic Canada Inc, Customer Care Centre at 1-300-561-5505, or web site or an
authorized Servicentre nearest you.
Reference pages are shown as black circled numbers Q.
Power
No power.
• Insert the AC power supply cord securely into the household AC outlet. O
The unit is automatically
switched to the standby mode.
•To conserve power, the unit automatically switches to the standby mode after approx.
30 minutes elapse in the stop mode (Auto power-off function). Turn the power back to ON.
Operation
No response when buttons
pressed.
•Some operations may be prohibited by the disc.
•The unit may not be operating properly due to lightning, static electricity or some other external
factor.
Reset procedure:
Press [POWER ci)/ij to switch the unit to the standby mode and then back to ON,
Alternatively, press [POWER (i)/i] to switch the unit to the standby mode, disconnect the AC
power supply cord, and then reconnect it.
No operations can be performed
with the remote control.
•Check the batteries are installed with the correct polarities (+ and -). O
•The batteries are depleted: Replace them with new ones.
Q
• Point the remote control at the remote control sensor and operate. O
Play fails to start even when
(play) is pressed.
Play starts but then stops
immediately.
• Condensation has formed; Wait 1 to 2 hours for it to evaporate,
•This unit cannot play discs other than DVD, Video CD and CD. ©
•This unit cannot play DVDs with a region number other than “1”, “ALL” or multiple region
numbers including "1". ©
•The disc may be dirty and may require cleaning. ©
• Ensure that the disc is installed with the label of the side to be played facing upwards. ®
Alternative languages fail to be
selected.
•An alternative language is not selected with discs which do not contain more than one language.
• In the case of some discs, the alternative language cannot be selected with [AUDIO) or
[SUBTITLE], Try selecting it from the disc's menu if one is available. ©
No subtitles.
•Subtitles appear only with discs that contain them.
• Subtitles are cleared from the television. Display the subtitles. ®
Soundtrack and/or subtitle
language is not the one selected
at the initial settings.
•The language is not recorded on the disc.
Angle cannot be changed.
•This function is dependent on software availability. Even if a disc has a number of angles
recorded, these angles may be recorded for specific scenes only. ©
You have forgotten your ratings
password.
Reset all the settings to Factory
Preset.
• While stopped, press and hold [k*<] (DVD-RV41, DVD-RV31, DVD-RV26) or [!◄◄,◄◄] (DVD-
RV21) and [II] on the unit and then also press and hold [,^] on the unit until “Initialized”
disappears from the television. Turn the unit off and on again.
All initial settings will return to the default values.
8
I
4=
£
Sound
No sound. :
Distorted sound. :
•Check the connections. © © ©
• Check the volume on the equipment you have connected.
• Ensure that the input settings for the television and stereo system are correct.
• If you have connected this unit to an amplifier through the AUDIO OUT terminals, go to the
Audio menu in the ACTION screen, and change “Speaker Setting" to suit your speakers. Select
“Yes” tor all the speakers you have connected. © Iti'Jtlrmil
• Sound will only come from the 2 front speakers if Advanced Surround is on. Turn Advanced
Surround off if you are using three or more speakers. ©
Piercing noise comes from the
speakers.
• If you have connected this unit to other equipment through the DIGITAL AUDIO OUT terminal,
ensure you have selected the correct settings for “Dolby Digital” and “DTS Digital Surround" in
the ACTION screen's Audio menu. ©
ROT5733