Panasonic MC-V9628 - Manual (Page 23)

REQUESTING SERVICE
A
WARNING
Ehctric Shack or Parsanai Injury Hazard
Disconnect the Blactrical supply befarB servicing or cleaning the unit Failure to do
BO could result in electric shack or personal injury from cleaner suddenly starting
Review Ihia chart to find do-il-yaurself aolutiana for minor performance problems
Any service needed, other than those described in these Operating Instructions,
should be performed by an authorized service representative
PROBLEM.
Claanar Won'l start
POSStBLH CAUSE
1 Unplugged al wall nullel
2 Tripped circuit breaker/bicwn fuse
at huusehold service panel
3 Lease hese electrical conneclians
4 Tripped Dverlaad praleclarin
POWER NOZZLE
POSSIBLE, 50LUTKIN.
1 Plug in firmly, push DN/DFF swllch In ON
2 Reset circuit breaker or replace fuse
3 Recenrset hose ends, (page 10)
4 Clean brush and brush supports,
then reset, [pages IB,19)
Poor |ab of dirt
pich-up
1 Full ar ctegged dust bag
2 Clogged airflow passages
3 Dirty safety filler
4 Wrong pile height setting
5 Open suction canlral
B Hate In hose
7 Warn POWER NOZZLE brushes
B Warn or broken bell
9 Dirty brush or brush supports
I d Canister hood open
1
2
3
4
5
B
7
B & S
ID
Change bag, (page IB]
Clear airflow passages, (page 1D]
Replace ftller, (page 17]
Ad]ust setting, (page 15)
Adjust oontral, (page 14)
Replace hose
Replace brush, (page 20)
See BELT CHANGING AND BRUSH
CLEANING, (pages IB]
Class and latch hood
Cleaner starts but
cuta nfl 1 Hose or hood eleclnoal oanneclions
2 Tnppsd ovsrtnad praleclor In
POWER NOZZLE
3 Tripped nvertoad protector
in canister
Check cannectinns, recarinecl hose
ends, (page ID)
Remove any Hems that may be oaugtil
□r jammed, then reset If clsanar starts
and stops again olaan brush and brush
supports, then reset, (pages IB 19)
Change dust bag clear airflow blockage
(page 21) Wail 50 minutes for motor
to cool and aulomalicallv reset
Power Nozzle will noi
run when etlached 1 POWER NOZZLE connecllons
unplugged
2 Wnm nr broken bell
3 Dirty brush or brush supports
4 Tripped overlaad pralector in
POWER NOZZLE
1 Plug In firmly, (page 9)
2&3 See BELT CHANGING AND BRUSH
CLEANING (pages 1 a)
4 Chech brush area for eircessive lint
build-up or jamming Clean brush and
brush supports, then reset, (pages IB, 19)
ntformancB indiEfllor,
aomo til adela. Is red
1 Full or clogged dusL bag
2 Dirty niter
3 Clogged airflow passage
4 Certain atlachmenl tools
1 Change bag, (page 1E)
2 Replace niter, (page 17)
3 Clear dog from airflow passage, (page 21)
4 This IS normal Llghl should go off
when tool 15 removed
Cleaner picks up maveeble
ruga -or- Power Nozzle
pusha loo hard 1 Wrong pile height setting
2 Suclion loo strong
1 Adjust setting, (page 15)
2 Dpen suction control, (page 11]
Light won't work 1 Burned out light bulb 1 Changa llghl bulb, (page IB)
Curd won't rewind 1 Dirty power cord
2 Cord Jammed 1 Clean Ihe power cord
2 Pull oul cord and rewind
Cleaner leaves marks
on carpsL 1 Wrong vacuuming pattern 1 See VACUUMING TIPS, [page 15)
- 2 3 -