American Access Systems Advantage DK - Regular - ADV-1000i - Manual (Page 12)

Page 12 American Access Systems / Security Brands, Inc.
Change the Master Code -- Sub-Mode 3
To change the Master Code:
• Enter the current Master Code
• Unit will sound a GOOD TONE• Press the numeral 3
• Enter a new Master Code
• Unit will sound a GOOD TONE
• If you make an entry error, simply press the star (ã) key and enter the number you wish
• Press the pound (#) key to exit the programming modeNOTES:
• Be sure to make a note of the new Master Code. It is the password to system operation.
• If the Master Code has been forgotten or lost, and you cannot enter Sub-Mode 3, you must perform a Master
Reset which will reset the Master Code to 1 2 5 1. You can then use Sub-Mode 3 to change the Master Code.
Set Sleep Code -- Sub-Mode 4
DETAILS: The Sleep Code is used to disable all Relay A and Function Codes from the keypad. This feature is most
commonly used in applications where no entry is desired after hours. Relay B codes will continue to be valid from
the keypad. By connecting both relays in parallel, managers may be assigned Relay B codes and still gain access.
While in the SLEEP MODE, the yellow and red LED’s will fl ash every 3 seconds. To initialize the system back tonormal,
simply re-enter the Sleep Code. Should you lose or forget the Sleep Code and the unit is in the sleep mode you must
complete a Master Reset. See the instructions on pages 20 and 21.
To program or change the Sleep Code:
• Enter the current Master Code
• Press the numeral 4
• Unit will sound a GOOD TONE
• Enter a new Sleep Code (If you hear an ERROR TONE, select another code that is not already in use)
• Unit will sound a GOOD TONE
• If you make an entry error, simply press the star (ã) key and enter the number you wish
• When the new Sleep Code is accepted you will hear a GOOD TONE
• Press the pound (#) key to exit the programming mode
Set Latch Code -- Sub-Mode 5
DETAILS: The Latch Code toggles the state of the main relay (A) of the circuit board. The red LED will remain lit while
the relay is in the latched position. The latch code is useful in applications where the gate is desired to hold open. If
the operator’s close circuit is controlled by loops, timers, etc., they will be overridden by the latched state of the relay
and the gate will hold open. An “OPEN-OVERRIDE” circuit must exist in the operator in order to utilize this function.
If your gate cycles when this code is entered, your operator is not set up to utilize this function. Your local dealer or
distributor should be able to assist you if you have any specifi c questions.
To program or change the Latch Code:
• Enter the current Master Code
• Press the numeral 5
• Enter a new Latch Code (If you hear an ERROR TONE, select another code that is not already in use
• If you make an entry error, simply press the star (ã) key and enter the number you wish
• When a new Latch Code is accepted you will hear a GOOD TONE
• Press the pound (#) key to exit the programming mode
• Now, when the new Latch Code is entered, the RED LED will light and the gate will hold open
• When the new Latch Code is entered a second time the RED LED will go off and the gate will close
NOTE: On gates with a closing timer, the “TIMED DURATION” begins when the Latch Code is released.
Set Relay Output Times -- Sub-Mode 6
To set or change a Relay Output Time:
• Enter the current Master Code • Press the numeral 6
• Enter the Relay numeral (1 = Relay A; 2 = Relay B)
• Enter the desired Relay Output Time in seconds (i.e., enter 060 for 60 seconds)
• Press the pound (#) key to exit the programming mode
Program Relay “B” Access Codes -- Sub-Mode 7
To program Relay “B” Access Codes:
• Enter the current Master Code
• Press the numeral 7
• Enter a new Relay B Access Code (If you hear an ERROR TONE, select another code that is not already in use)
• When a new Latch Code is accepted you will hear a GOOD TONE
• Continue to enter new Relay B Access Codes
• If the memory becomes full, you will not be able to add more Relay B Access Codes
• Press the pound (#) key to exit the programming mode
Note: If the memory is full, you will not be able to access Sub-Mode 7. You will hear an ERROR TONE
instead.