Cuisinart CSB-55 - Manual (Page 7)

Mini Chopper Grinder Storage.
The SmartStick™ Mini Prep ® Chopper Grinder Attachment stores neatly on
the countertop in a minimum of space. Store the unit assembled to prevent loss
of parts. Store the blades as you would sharp knives—out of reach of children.
Chopper Grinder Parts and Assembly
Reversible Blade.
The Cuisinart SmartStick™ Mini Prep ® Chopper Grinder attachment is
equipped with a reversible blade. This blade is sharp on one side and blunt
on the other. The blade is attached to a plastic ring which slides over the
blade assembly shaft, so it can be easily turned over to select the appropriate
blade. A guide for proper blade selection follows in the section, Chopper
Grinder Tips for Processing Foods.
Before you process any food, assemble the parts.
1. Place the Prep Bowl on a flat, dry, stable surface. It should be close to an
electrical outlet of the same voltage as stated on the rating plate on the
SmartStick™ Hand Blender.
13
The counter storage unit can be placed in a cupboard or on a shelf if not on
the counter.
Wall Mount Option
Separate the two plastic storage stand pieces. You will need only one for wall
mount. (See diagrams below). The unit you must use is the section that has
the round storage hole to hold the whipping disk.
When selecting a mounting location, be sure to leave enough room above the
storage stand for your hand to remove the SmartStick™ Hand Blender. Also be
sure to leave enough room below the stand to allow the appliance to hang freely.
You will need to drill two holes 2 5/8" apart from each other, measured from
the center of each hole. To assist in proper location of holes for the mounting
screws, remove the wall mount template from this instruction book. Place the
template over the back of the wall unit, aligning the outline of the template
with the wall bracket. When you have done this, place the template and wall
bracket against the wall in the desired location. Remove the wall bracket,
leaving the template in place. Mark the wall with a pencil in the locations for
screw holes indicated by the template. Remove the template.
With a drill, make a 3/16" starter hole for each screw. Place the plastic
anchor in each hole. Push completely into the hole with fingers, or tap in
gently with a hammer. Screw a mounting screw into each hole leaving 1/8" to
1/4" of the head and screw exposed.
Position the two mounting holes of the wall bracket over the screw heads and
slide wall bracket down the wall until the bracket is resting against the screw
head, and will not slide any further. If the wall bracket feels too
loose against the wall, remove bracket, put screws further into
wall and replace bracket.
Place the assembled SmartStick™ Hand Blender into the wall
bracket. The unit will hang from the bracket, held in place by
the motor body width.
To reduce the risk of fire or electric shock, do not operate any
heating appliance beneath the mounting unit.
Do not mount the storage bracket/ unit over or near any portion of a heating
or cooking appliance or a sink or basin.
12
A. Chopper Grinder
Prep Bowl
B. Cover Slots (3)
for Attaching
Cover
C. Metal Blade
Assembly Shaft
D. Rubber Feet
E. Blade Assembly
F. Blade Ring
G. Plastic Blade
Sheath
H. Chopper Grinder
Cover
I. Lift Tabs
J. Chopper Grinder
Spline
K. Central Hub
Holding Ribs
L. Curved Sharp
Edge
M. Flat Blunt Edge
N. Ridges for
Gripping
SmartStick ™
MINI PREP ® Chopper Grinder Attachment
®
A
B
C
D
J
H
I
G
N
K
L M
F
E
F
G
SmartStick™ MINI PREP® Chopper Grinder Attachment
®
PRESS BUTTON TO DETACH
SmartStick TM
EXTENDABLE SHAFT
®
® SmartStick ™ MINI PREP® Chopper Grinder Attachment
E
F
G
Wall
Anchor
Anchor
Bolt
PRESS BUTTON TO DETACH
SmartStick TM
EXTENDABLE SHAFT
®
® Use only this piece for wall mounting. Connect to other half for countertop storage.
CSB-55 IB-3028D 8/12/03 6:52 PM Page 12