Cuisinart CSB-55 User Manual
Page 8
PRESS BUTTON TO DETACH
SmartStick
TM
EXTENDABLE
SHAFT
®
®
SmartStick
™
MINI PREP
®
Chopper Grinder Attachment
PRESS BUTTON TO DETACH
SmartStick
TM
EXTENDABLE
SHAFT
®
®
SmartStick
™
MINI PREP
®
Chopper Grinder Attachment
of the Plastic Blade Sheath. Let the Blade Ring slide down to the bot-
tom of the Plastic Blade Sheath. The lower blade should almost touch
the bottom of the Prep Bowl.
Lift the Prep Bowl, holding it firmly from the bottom. Pick up the Blade
Ring by its hub holding ribs (grips) and turn it very slightly clockwise.
This locks it in place on the Plastic Blade Sheath and prevents it from
sliding up during processing.
3. Connect the SmartStick™ Hand Blender
Motor Body to the top of the Chopper
Grinder Attachment Cover. Align the spline
in the Chopper Grinder Cover’s drive shaft
with the ribbed opening on the underside of
the motor body. When aligned properly, slide
the two pieces together until they mate. You
will feel and hear a slight click. It may be
helpful to press the rubber release button
when sliding these pieces together.
4. With the Hand Blender in place, locate the
Chopper Grinder cover and place it on top of
the prep bowl.
4a. Be sure that the 3 ridges at the top of the
Blade Assembly line up with the 3-arm
propeller gear in the underside of the chopper grinder cover, and that
the cover is seated all around the top of the prep bowl.
4b.To properly seat the cover you must line up the three molded pins from
the cover with the 3 slots at the top of the Prep Bowl. Rotate cover
counterclockwise to secure it to the prep bowl. Rotate the cover until
the pins are in the far left position in the slots.
15
2. The metal blade assembly shaft is attached to the bottom of the Prep
Bowl. If not already in place, slide the fully assembled Blade Assembly over
the top of the blade assembly shaft.
2a. Putting together the Blade Assembly:
Connect the Blade Ring (F) to the Plastic Blade Sheath (G). Line up the
blade ring opening with the plastic sheath. Let the blade ring slide to the
bottom of the plastic sheath. HOLD THE BLADE RING BY THE
CENTRAL HUB HOLDING RIBS (grips)(K) ONLY. DO NOT
TOUCH THE RAZOR SHARP BLADES.
Note these important features of the Blade Ring. The Blade Ring can be
placed over the Plastic Blade Sheath in two different ways:
If you hold it this way (A), you will see the word “Sharp” on the blade.
Assemble the blade this side up to use the sharp edge. (see the section on
processing food for information about when to use the sharp edge.)
If you hold it this way (B), you will see no writing on the blade. Assemble
the blade this side up to use the blunt edge. (See the section on processing
food for information about when to use the blunt edge.)
There are notches (C) on opposite sides of the interior of the hub. These
fit over ridges on the sides of the Plastic Blade Sheath.
Pick up the Blade Ring by its hub holding ribs (grips) and line up the
notches in the interior of the Blade Ring hub with the ridges on the sides
14
A.
SHARP SIDE
B.
BLUNT SIDE UP
C.
Notch
N
F
G
K
2a
4a
4
Inside View
of Prep Bowl
Inside View
of Chopper
Grinder
Cover
PRESS BUTTON TO DETACH
SmartStick
TM
EXTENDABLE
SHAFT
®
®
SmartStick
™
MINI PREP
®
Chopper Grinder Attachment
PRESS BUTTON TO DETACH
SmartStick
TM
EXTENDABLE
SHAFT
®
®
SmartStick
™
MINI PREP
®
Chopper Grinder Attachment
4b
3
Motor
Body Bottom
and Chopper
Grinder
Cover Top
View
CSB-55 IB-3028D 8/12/03 6:52 PM Page 14