Single surface element, Dual surface element, Warmer surface element – GE ELECTRONIC TOUCH CONTROL PP980 User Manual

Page 7: Surface elements -9

Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".

Advertising
background image

OFF

©

OR

0

Single Surface Element

To turn on a sintjle surface element:

Touch the

ON/OFF

j>ad, then touch

^— the f+J/^Jpad.

ge.com

To turn off'a single surface element,
touch the

ON/OFF

pad again.

Use the (+)/(-) jjdd to choose the
desired power setting. The control

will beep each time a pad is touched.

I

I

S'.

I

OFF

0

OR

©

SIZE SELECT

Dual Surface Element

The dual surface element has a pan
sizing sensor which will automatical!)' set
the small or large suiface element to
match the size of your pan (see the

Using

Pan Sizing

section). To override the

automatic jran sizing sensor and select
the small or large suiface element:

VJi Touch the dual surface element

^ O/V/Off

pad.

^ Use the {+)/f-^pad to set the desired

power setting.

^ Touch the

SIZE SELECT

once to

turn on the large surface element.
Touch the pad again to turn on the
small surface element.

Wien the indicator light next to the

SIZE SELECT

pad is on, the large surface

element is on. When it is off, the small

suiface element is on.

To turn the dual surface element off,

touch the

ON/OFF

pad.

CB
su

a

sa.
D

cB*
a
3‘

«3

©

OR

0

Warmer Surface Element

To turn on the warmer surface element:

Touch the ON/OFF pad, then touch

the WARMEEpad. The suiface
element will turn on to w'amier

power setting W1 (low).

2 Use the (+)/H pvl to choose

additional settings of W2(medium)
and W3 (high).

To turn off the w'amier power settings,
touch the ON/OFF pad. To change from
the wanner settings to regular cooldng
settings, press the WARMER pad. The
surface element will be on pow'er setting

I. (low). The suiface element inav then
be set to the desired setting using the
M/f-jpads. To turn off the surface
element, touch the ON/OFF pad again.

Food Type

Control Setting

Breads/Pastries

W1

(LOW)

Sauces

W2

(Medium)

Soups (cream)

W2

(Medium)

Stews

W2

(Medium)

Vegetables

W2

(Medium)

Hot Beverages

W3

(HIGH)

Soups (liquid)

W3

(HIGH)

The chart above shows initial suggested settings

only. The temperature, type and amount of food,
and the time held will affect the quality of the

food.

CAUTION: Do not warm food on the WARMER
for more than two hours.

Do not use plastic wrap to cover food. Plastic

may melt onto the surface and be very difficult

to remove.

Use only cookware recommended for top-of-range
cooking.

The

WARMER

will keep hot, cooked food

at sening temperature. .Alwatt; start with
hot food. Do not use to heat cold food.

Placing uncooked or cold food on surface

warmer could result in foodbarne illness.

For best results, all food on the

WARMER

should be covered with a lid or

aluminum foil. Wien w'amiing pastries
or breads, the cover should be r ented to
all ow moisture to escape.

j'Uways use potholdeix or oven mitts when

removing food from the

WARMER

as

cookware and ¡jlates will be hot.

A hot surface indicator light will glow'
when the glass suiface is hot and tvil!

remain on until the surface has cooled
below' l.aO°F.

Advertising
This manual is related to the following products: