Kenmore ULTRASOFT 400 625.38845 - Manual (Page 10)

jjajj j-jjjjjj jj
SECTION 2 HOW YOUR WATER SOFTENER WORKS
A. FACEPLATE TIMER FEATURES
s
c
T
I
o
N
ijjjjjjjjjjjjjjjjj
ijjjjjjjjjjjjjjjjj
ijj ^F^IS jjjjjjjjjj
M47999ÏJjjjjjjjjj
UJajJJJJJ JJJ.4JJ JJ ijjjjjjjjjjjj^jjjj
IJJJ.IJ-MJJJJJ4JJ JJ
^ EXTRA RECHARGE
Sometimes, a manually started
regeneration (recharge) may be
desired, or needed. Two exam­
ples are:
- You have used more water than
usual (guests visiting) and you
may run out of soft water before
the next timer started regenera­
tion.
- You did not refill the softener
with salt before it was gone. After
you refill with salt:
You can start a regeneration right
away, or you can set the timer to
regenerate at the next 2:00 AM (or
other preset recharge time). Do
the following.
108'
^ RECHARGE NOW
Press the ON/OFF-HOLD but­
ton and hold until ^RECHARGE
NOW, Serv and Fill begin to flash
in the display. Upon reaching
fiU, the first cycle of regenera­
tion, the flashing Serv turns off and FiU is on steady.
RECHARGE continues to flash. This regeneration
win last for about 2 hours. After the 2 hours, you will
have soft water again.
*Note:
If the CLEAN feature is set to ON, a cleaning back­
wash {CLEAN and Bkwsh or Rinse flashes in the dis­
play, along with the minutes of the clean cycle re­
maining) precedes the recharge.
► RECHARGE TONIGHT
'HiOi'n
PM r-uo
RECHAPGE TONfOHt
Press and release {do not hold) the
ON / OFF-HOLD button. RE­
CHARGE TONIGHT Hashes in
the display, and the softener be­
gins regeneration at the next
preset recharge time. Press and release the ON/
OFF-HOLD button once more if you decide to can­
cel the regeneration, and RECHARGE TONIGHT.
^ SALT MONITOR SYSTEM
The faceplate timer has a low salt monitor with an
indicator light to remind you to refill the storage
tank with salt. To set this monitor system:
Lift the salt hole cover and level the salt in the
storage tank.
The salt level decal, on the brinewell inside the
tank, has numbers from 0 to 8 (see drawing be­
low). Observe the number the leveled salt is at
or closest to.
Now, press the SALT LEVEL ADJUST button
until black bars display up to the salt level num­
ber. For example, the pictures below show the
salt level at 6.
q I Finally, set the level you want the low salt indi­
cator light to come on. Press the SIGNAL LIGHT
ADJUST button until a (^) shows opposite this
number. In the example below, the light will
come one when the stored salt drops to level 2.
At level 2, the storage tank is about 1/3 fuU. This
is the lowest you should allow the stored salt
level to drop to.
If you want to turn the salt monitor off, press the
SIGNAL LIGHT ADJUST button until OFF
shows above.
Note:
For accurate salt monitor operation, always use
nugget or pellet water softener salt. See page 1-6.
If potassium chloride is used, be sure to adjust the
timer to the KCl setting on page 1-4.
2
-
1
Problems, Questions? Call 1-800-426-9345 Kenmore Water Line