Kenmore 106.511800 - Manual (Page 19)

■ COOLING Obl/C№f‘ HOLD 3 ^ -
2 .
Water / Ice Light Temperature Settings Lock Measured Fill
HOLD 3 ж: HOLD 3 SEC
[...... ..........................I
Press WATER/ICE to manually turn off the Measured Fill
feature.
NOTE: The dispenser will automatically turn off Measured
Fill after 1 minute of inactivity. When Measured Fill is turned
off, any changes you have made will be lost and all defaults
will be restored.
You can dispense water by the ounce, cup, or liter. The
default unit is ounces. To switch to cups or liters while the
Measured Fill feature is already on, press the MEASURED
FILL button to toggle through the available units.
Default, minimum, and maximum volumes are listed below.
Units Default Minimum Maximum
Ounces 8 1 128
Cups 1 1/4 16
Liters 0.25 0.05 4.00
3. Press the SETTINGS and TEMPERATURE buttons to adjust
the volume as desired. The SETTINGS button increases the
volume, and the TEMPERATURE button lowers the volume.
NOTE: Most coffee cups (commonly 4 to 6 oz [118 to
177 mL] per cup) are not the same size as a measuring cup
(8 oz [237 mL]). You may need to adjust the volume to avoid
unintentionally overfilling coffee cups.
4. You can save one “favorite” volume for repeated use. Adjust
the settings until the desired volume is displayed, then press
LOCK to save the volume. In future Measured Fill use, press
LOCK to access the saved volume setting.
NOTE: You can only save one “favorite.” Saving a new
volume will overwrite the previously-saved “favorite.”
5. To dispense water, press a sturdy glass against the dispenser
pad OR place the glass below the dispenser opening and
press either the DISPENSE WATER button or the LIGHT
button.
NOTE: While dispensing water, the digital display will count
down how much water remains to be dispensed, according
to the volume you selected. The flow of water will
automatically stop once the desired volume has been
dispensed.
6. To stop dispensing before the selected volume has been
dispensed, remove the glass from the dispenser pad OR
press either the DISPENSE WATER button or the LIGHT
button a second time.
NOTE: If you stop dispensing before the desired volume has
been dispensed, the digital display will continue to show
how much water remains to be dispensed. The display will
turn off after 1 minute of inactivity.
The Ice Dispenser
Ice dispenses from the ice maker storage bin in the freezer when
the dispenser pad is pressed. To turn off the ice maker, see “Ice
Maker and Storage Bin.”
Your ice maker can produce both crushed and cubed ice. Before
dispensing ice, select which type of ice you prefer by pressing
the WATER/ICE button.
The display screen indicates which type of ice is selected.
\zj \zJ
CRUSHED CUBED
For crushed ice, cubes are crushed before being dispensed. This
may cause a slight delay when dispensing crushed ice. Noise
from the ice crusher is normal, and pieces of ice may vary in
size. When changing from crushed to cubed, a few ounces of
crushed ice will be dispensed along with the first cubes.
To Dispense Ice:
1. Make sure the desired type of ice is selected. To switch
between cubed and crushed, press WATER/ICE.
AWARNING
Cut Hazard
Use a sturdy glass when dispensing ice.
Failure to do so can result in cuts.
2. Press a sturdy glass against the dispenser pad. Hold the
glass close to the dispenser opening so ice does not fall
outside of the glass.
IMPORTANT: You do not need to apply a lot of pressure to
the pad in order to activate the ice dispenser. Pressing hard
will not make the ice dispense faster or in greater quantities.
NOTE: To dispense both water and ice at the same time,
press the DISPENSE WATER button while using the dispenser
pad to dispense ice.
19