Kenmore 665.72002 - Manual (Page 24)

TROUBLESHOOTING
Try the solutions suggested here first in order to avoid the
cost of an unnecessary service call.
Nothing vnrill operate
Is ttie power outlet properly wired and polarized?
Try another outlet to check for proper wiring and polarity.
Is the power supply cord unplugged?
Plug into a properly grounded 3 prong outlet. :
: : : :
Has a household fuse been blown or has the circuit
breaker been tripped?.......
Replace the fuse or reset the circuit.
Is die main or regulator gas shutoff valve in the off
position? ■■ ■■■■■ ■...... ■ ■ ■ ■ " "■........... ^i
See. Installation instructions. : ::: :
: :
■ Is die range properly connected to the gas supply?
Contact a Sears trained repair speciaiist or see Installation.
Instructions. - ..... , ; .......... . ■
Surface tairners will not operate
■ Is this the first time the surface burners have been used?
:; Turn on any one of the surface burner knobs to release air
from the gas lines, i
■ On some models, is the Cooktop Lockout set?
- See ''Cooktop Lockout" section.
■ Is die control knob set correctly?
: Push in knob before turning to a setting.
■ Are die burner ports clogged?
: :See "Sealed Surface Burners" section. ;:
Surface tairner flames are uneven, yellow and/or noisy
Surface burn^ makes popping noises
Is the burner wet?
Letitdry, ::
::
Excessive heat around cookware on cooktop
Is the cookware the proper size? ....
Use cookware about the same size as the surface cooking
area, element or surface burner. Cookware should not extend
more than 1 in. (2.5 cm) outside the cooking area. :
:::
■ Is the power outlet properly wired and polarized? T
; . Try another o.utletto check for proper wiring and polarity.
■ Is this the first time the oven has been used?
Turn any one of the surface burner knobs on to release air.
from the .gas .lines," : : : : ; ; ; : ; ;
Is the electronic oven control set correctly?
See "Electronic .Oven Control” section.
On some models, is the Oven Lockout set?
;Se.e."Oven Lockput" section. ; ;; f;
Are die burner ports clogged?
. Se.e"S.eaieci.Surface Burners" section.
Are die burner caps positioned properly?
See..’’Seaied .Surface Burners" section. ::
Is die burner damaged? ................ ...........
On models with caps, look for a warped cap. If cap will spin
freely on a flat surface, painted side down, the cap is warped.
Switch cap with a different surface burner to check for further
warping. Contact a Sears trained repair specialist. See back
c
o v e r . ■ ■ ■ ■ .......
Is propane gas being used? ....
The appliance may have been converted improperly. L .
Contact a .Sears .trained repair specialist. See back coyer,.
Oven burner fails to light
A household fuse has blown or a circuit breaker has been
tripped. V )
::: ■
The ignition system is broken. Contact a Sears trained repair
technician. See back cover. :
Oven makes muffled ticking noise when in use
■ This is normal and occurs when the oven burner cycles on
:: and off to hold the set oven temperature. : : : : : : :
Oven burner lights, then goes cait after 1 minute
■ . Press OFF/CANCE.L, then wait 1 minute before trying again...
■ Is the power outlet properly wired and polarized?
;;; Try another outlet tp check for proper wiring and polarity.
Oven burner flames are yellow or noisy
■ Is propane gas being used? ........ ^ ^
.. .\The appliance may have been converted improperly. Contact
. ; ; ; a. Sears.traitied repair specialist. See back cover. : ;
Oven temperature too high cff too low
■ Does the oven temperature calibration need adjustment?
; ; ; ; ;; See "Oyen Temperature Control” section,
24