Kenmore ENVIROSENSE 85500 - Manual (Page 6)

For your conwsniance, all thre« fillers (Pre­
Fitter. Washable Nano-Silvsr/Carbon Filter,
and True HEPA Filter) come in one pre­
packaged replacement cassette.
For optimum unit efficiency, wash the Pre­
Filter and Washable Nano-Silwer/Carbon
Filter as described betow (Filter Cleaning)
every three months.
Do not wash and reuse the True HEPA
Filter—(t will not work effectively.
WARNING: Before replacing or cleaning
any filters, make sure to remove the
power plug front the wall outlet.
Replacemeitt Procedure
1. Remove the frorit panel by pulling gently
on the sliver labs
located on eadi side
of the unit.
2, Pull out the filter cassetteby grasping the
black tabs located
on eadt side.
3. Remove the plastic wrap from tha new
filter cassette.
4. Place the new filter cassette in the
main unit.
5. Replace the front
panel.
6. Plug in the power cord to a wall outlet
and turn on the unit.
7. To turn off the CHANGE FILTER
INDICATOR, press the FUNCTION and
OFF TIMER buttons at the same time for
five seconds: the CHANGE FILTER
INDICATOR will flash five times and turn off.
Filter Cleaning
We recommend leaning the Pre-Filter (A)
and the Nano-Silver/Carbon Filter ¡C) every
three months with normal use. The interval
between cleanings will vary based on room
conditions.
1. Remove the front panel and filter
cassette as described in Replacement
Procedure.
2. Remove the Pre-Filter by gently puling
one side of the cassette frame outward
while lifting the Pre-Filler tab at the same
time. When one edge is clear of the
frame, the Pre-Filter will slide out for
cleaniftiill
3. Lightly vacuum the Pre-Filler and wash
with water and a mild household deter­
gent. Rinse, and shake off excess water.
4. To remove the Washable Nano-S liver/
Carbon Filter, turn the cassette over and
place facedown on an even surface.
Grasp the tali white tab nearest to the
gray lab. Slightly flex the cassette frame
outward while pulling up on the gray
iab. When the first corner is released,
pull Qui on the other tall frame tab while
a>ntinuing to pull up on the gray lab.
When one long edge of the filler is free,
slide out for cleaning.
5. Wash the filter in warm water with a mild
household detergent. Rinse, and shake
off excess water.
6. Do not dry the two filters—running the
unit will be suffident to dry them.
7. Replace each filter in the cassette frame
by inserting one tong edge first, then
snapping into place by pushing sideways
and down at the same lime. Make sure
both filters are completely inside the
cassette frame and secured by the short
tabs. If a filter is on top of one or more
tabs, pull outward, slightly flexing the
cassette frame, while gently pushing
down on the edge of the filter.
6, Replace the filter cassette and front
panel as described In Replacement
Procedure.
a Plug in the power cord to a wall outlet
and turn on the unit.
Note; Never attempt to remove the True HEPA
Filter from the cassette frame. Never attempt to
dean the True HEPA Filler. Replace the entire
cassette only when CHANGE FILTER alert
acSvates, (Modd 85500 replacanenf #85501;
Model fS501 replacement #85511)
NANO-SILVER/CARBON FILTER
CASSETTE
SHORT
GRAY TAB
CASSETTE
LONG TAB
FRONT SIDE
Plasma Doctor’^“
Display Panel
DC Motor
Washable Nano-
Sitver/Carbon Piter
Filter Cassette with
True HEPA Filter inside
Front Panel
Power Plug
Remote
ConlroJ
Air Outiel Cradle
TOPSIDE
XJ