RCA RCR4383 - Manual (Page 3)

LED
Direct Code Entry
To use the direct code entry method to program your universal
remote to control your compt)ncnts, ibllow the steps below.
1. Manually turn on the component you want the remote to
control (TV. VC^R, DVD, DVR, satellite receiver, or cable box).
2. Locate the enclosed Code Lists. Find the list for the
component you wish to program. l*ind your component’s
brand. You will see a listing of four-digit codes for each
brand. If your brand isn’t listed, use one of the Code Search
methods to program the remote control. (Refer to pages 3-5
for Manual and Auto Code Search methods.)
Note: y^u can also use the online code finder at
Terww.rca.com/codefinder to find the best codefor your component.
3. Press and hold the component
key (TV, SAT-CRT.. DVD-VCR.
DVR-AUX) you wish to program.
The LTD turns on and remains on.
Keep holding down die component
key. If you relca.se the component
key any lime during the Direct
Code Entry procedure, the I.ED blinks four limes, and
the process is exiled. Tlie last programmed code under the
component key is retained.
Notes:
• lb pTOff'am the DVD* VCR key to control a VCR, see paff 3.
• To program the DVR*AUX
to control a componetit other than
a DVR, seepage 4.
4. While holding down the component key, consult the
Code Lists for die four-digit code that corresponds to your
component’s brand and use the number keys (0-9) to enter
it. After you press the first number, the LED turns off. After
the ft)urth number is entered, the LED turns on.
TIP: Throughout the programming of each key, be sure to keep the
remote pointed at the IR sensor of the component you are currently
programming the remote to control.
5. Release the component key. If the LED turns off, you
have entered a valid code and have followed the correct
procedure for Direct Code Entry. Proceed to die next step.
If the LED blinks four times, you have cither entered a code
number that is not in the code lists or missed a step in the
code entry procedure. Repeal the Direct Code Entry process
from step 3 and try the next code listed.
6. To confrrm that the component key is programmed with the
correct code for maximum functionality, test die component.
Attempt to control a variety of die component's functions
widi die remote. If some features of your componenrs do not
work, try pro^mming the remote vidth a different code in the
list until you find the code that allows the remote to control
die majority of your component’s fimcdons. Different codes
can provide different levels of functionality.
IMPORTANT: Remember to enter the codeforfuture reference in
the box prmnded in the Code Retrirval section of this manual. (See
Manual Code Search and Entry
If your component’s brand isn’t listed in the Code Lists, or if
you have tried all of the codes for your brand and the remote
docs not operate your component, try one of the 0>dc Search
methods below-Manual Code Search or Auto Code Seardi.
Both Code Search inediods cycle through all of the codes in
the Code Lists in the event that your component’s code is
listed under another brand.
Note: The Manual Code Search method mery take a long time
because the remote searches through all of the codes in its memoryfor
the code that operates your component. Therefore, if your brand is
listed in the Brand Codes or the Code Lists, first try the Brand Code
Search or the Direct Code Entry method described on pages 2-3.
CLEAR TIP: To exit without saving at ary point in the Manual
Code Search, press and release tht CLEAR key.
r~----- lo
rr »и-ал ем»м4Д1 oooo
1. Manually turn on the component you want the remote to
control (TV, VC.R, DVD, DVR, satellite receiver, or cable box).
Notes:
• Tbproff-am the DVD*VCR to control a VCR, see paged.
• To program the DVR* A UX key to control i component other than
a DVR. see page 4.
Press and hold die component
key (TV, SATCBL, DVD-VCR,
DVR-AUX) you wish to program. Tlie
I£D turns on and remains on. Keep
holding down the component key.
While holding the component key
down, press and hold the POWER
key. The IJID turns off. After holding down both keys for
three seconds, the LED turns back on.
4. Release both keys. Tlie LED remains on.
Note: If you press an invalid key during Manual Code Semeb, tlic
remote does not respond and the search times out after two minutes.
When the search times out, the LED blinks Jour times and turns off.
The last programmed code under that component key is retained.
TIP: Ihrougfout the programming ofeach key, be sure to keep the
remote pointed at the IR sensor ofthe component you are current^
programming the remote to control.
5. Press and release the POWER key repeatedly until your
component turns off. Eacli lime you press the POWER key,
the LED blinks, and the next code in the list is sent. Tliis
process continues until all of the codes in the Code Li.srs
have been tried. If your component turns off, you have
found the correct code. (If it cycles through and the LED
blinks four times and turns off, all codes have been searched.
The Manual Code St^ch. meiiiod is exited.)
TIP: Because there are so many codes, you may bazHt to press the
POWER key many times—possibly hundreds of times.
STOP 6. Once you have found the conecT code, you must save
the new code by pressing and releasing die STOP key.
The I.ED turns off You must press the STOP kc 7 to
save the code or the cottcci code will not be stored!
When you press die STOP kc>', die code i.s stored.
7. Be sure to retrieve the code your remote programmed by
finishing the Code Retrieval process found on page 5.
Programming the DVD*VCR Key to Control a VCR
The DVD-VCR key defaults to control a DVD player. If you want the DVD-VCR key to control a VCR, you must preprogram
thcDVD-VCRkey.
1. Press and hold the DVD-VCR key. The LED turns on. Keep holding down the DVD-VCR key.
2. While holding down the DVD*VCR key, press and release the number 2 key on the keypad. The LED turns off.
3. Release the DVD-VCR key. The LED blinks four times and then turns off. The DVD-VCR key i.s now “set" to control a VCR.
4. Next, program the DVD-VCR key to control the brand of VCRyou have. Remember to consult the VCR code list.