G-Shock GW-201NT-1 - Manual

2016-1
Module No. 2016
M
A B
C
P
ABOUT THIS MANUAL
• Button operations are indicated using the
letters shown in the illustration.
• Each section of this manual provides you with
the information you need to perform
operations in each mode. Further details and
technical information can be found in the
“REFERENCE” section.
(MODE)
Warning!
Note the following important points concerning Identification Mode data
stored in the memory of this watch.
•
SCUBA diver certificate number, passport number, and emergency
contact number data stored in the memory of this watch can be
misused whenever the watch is in the hands of another party.
P
P
P
P
Site Mode
Press
M
.
Identification Mode
Alarm Mode
Countdown
Alarm Mode Stopwatch Mode
▲
▲
▲ ▲
▲
M
A B
C
P
GENERAL GUIDE
• Press M to change from mode to mode.
•
While in any mode hold down M for one second, to enter the Dive Time
Measurement Mode.
• In any mode, press B to illuminate the display.
TIME
P
DIVE
▲
▲
Dive Time
Measurement
Mode
Hold down M .
Timekeeping Mode
▲
• To protect against the misuse of SCUBA diver certificate number,
passport number, and emergency contact number data, input them
in coded form that cannot be understood by others.
• Make sure you correctly input your name and blood type data.
Once you input your data, take care that the watch is not borrowed
by another person. Otherwise, emergency medical personnel may
assume that your data applies to the person who borrowed the
watch.
• The default blood type screen setting when you first purchase the
watch or after you change the battery is “
A ” for the blood type and
“ Rh * ” for the Rh factor. To avoid problems caused by display of
the wrong blood type, we recommend that you input your correct
blood type data as soon as possible after purchasing the watch
and after having the battery replaced.
• CASIO COMPUTER CO., LTD. shall not be held liable to you or any
third party for any losses or damages suffered through the misuse
of data stored in the memory of this watch.
Read This Before You Set the Time and Date!
The times displayed in the Timekeeping Mode and Site Mode are linked.
Because of this, make sure you select a “Home Site” (the site whose time
and date you are setting), before you set the date and time. You can use
any one of the 10 snorkeling and scuba diving sites pre-programmed in
watch memory, or you can create your own.
Site Name GMT Differential Location
CAYMAN
GALAPAGOS
GBR
GUAM
HAWAII
JAPAN
MAURITIUS
MALDIVES
RED SEA
TAHITI
Caribbean Ocean
West Pacific Ocean
Coral reef north east of Australia
East Pacific Ocean
Central Pacific Ocean
East Pacific Ocean
West India Ocean
North India Ocean
Red Sea
South Pacific Ocean –5
–6
+10
+10
–10
+9
+4
+5
+2
–10
M
A B
C
P
TIMEKEEPING MODE
In addition to normal timekeeping, use the
Timekeeping Mode to set the current time and
date. You can also view the Dive Time
Measurement Mode log data.
• See the section of this manual that describes
the Dive Time Measurement Mode for
information about log data.
Day of week
Month – Day
Hour : Minutes
PM indicator
Seconds
M
A B
C
P
Important!
If the site you want to use as your Home Site is not in the above list, use the
procedure under “Changing Site Data” to edit the pre-programmed site data.
To set the time and date
1. In the Timekeeping Mode, hold down A until
the seconds digits start to flash.
2. While the seconds digits are flashing, press
C to reset the seconds to 00 .
• Pressing C while the seconds count is in
the range of 30 to 59 resets the seconds to
00 and adds 1 to the minutes. In the range
of 00 to 29, the minutes count is
unchanged.
Site name
3. Press M to move the flashing in the sequence shown below to select
other settings.
Seconds Hour Minutes
Site
Name
Year
DST
On/Off
12/24-Hour
format
Month Day
• See “Daylight Saving Time (DST)” for details on DST On/Off setting.
4. Press M until the site name is flashing on the display.
5. Use B and C to scroll through the site names until the one you want
to set as your Home Site.
•
Pressing C scrolls forward, while B scrolls back through site names.
• See “Read This Before You Set the Time and Date!” for a list of site
name.
6. Press M until the hour setting is flashing on the display.
7. Press C to increase the setting or B to decrease it.
8. Repeat steps 6 and 7 to set the minutes, year, month, and day.
• When the 12/24-hour setting is selected, press C to toggle between
12-hour ( 12H ) and 24-hour ( 24H ) timekeeping.
9. Press A to return to the current time screen.
M
A B
C
P
DST
Daylight Saving Time (DST)
Daylight Saving Time automatically advances the time setting by one hour
from Standard Time. Remember that not all countries or even local areas
use Daylight Saving Time.
To toggle your Home Site time between DST and Standard Time
1. In the Timekeeping Mode, hold down A until
the seconds digits start to flash.
2. Press M twice to move the flashing to the
DST On/Off setting.
3. Press C to toggle Daylight Saving Time
( O ) and standard time ( OFF ).
4. Press A to return to the current time screen.
•
The DST indicator appears on the display
to indicate that daylight saving time is
turned on.
DST indicator