Alarm mode, Countdown alarm mode – G-Shock GW-201NT-1 User Manual
Page 3
2016-3
•
In the case of
BLOOD TYPE
, you can input a blood type (ABO)
and Rh factor.
Viewing Identification Mode Data
In the Identification Mode, each press of
C
scrolls through the data in the
sequence shown below.
NAME
C CARD
EMERGENCY NO.
PASSPORT
BLOOD TYPE
•
In the Text Area, the title alternates with the input text.
Inputting Text and Numbers
The following procedure is the same for
N A M E
,
C C A R D
,
EMERGENCY NO.
, and
PASSPORT
data.
M
A
B
C
1. In the Identification Mode, display the title of
the data you want to input.
2. Hold down
A
until the cursor appears in the
text area.
•
If you do not want to input text into the text
area, press
M
16 times to move the cursor
to the number area and jump to step 7.
3. Use
B
and
C
to change the character at the cursor position in the text
area. The character changes in the following sequence.
-
)
Press
C
.
Press
B
.
(space)
1
to
0
A
to
Z
(
/
.
4. When the character you want is at the cursor position, press
M
to move
the cursor to the right.
5. Repeat the steps 3 and 4 until your text is complete.
6. After you input text, use
M
to move the cursor to the number area.
•
The text area in the Identification Mode can hold up to 16 characters.
When the cursor is located at the 16th space of the text area, moving
the cursor to the right causes it to jump down to the first digit in the
number area. When the cursor is at the 10th digit of the number area,
moving it to the right causes it jump back up to the first character of
the text area.
7. Use
B
and
C
to change the character (hyphen, number, or space) at
the cursor position in the number area. The character changes in the
following sequence.
x
(space)
0
to
9
Press
C
.
Press
B
.
8. When the character you want is at the cursor position, press
M
to move
the cursor to the right.
Cursor
M
A
B
C
9. Repeat steps 7 and 8 until you complete number input.
10.Press
A
to store your data and return to the Identification Mode data
screen (without the cursor).
Inputting Your Blood Type
1. In the Identification Mode, display the
BLOOD TYPE
title.
2. Hold down
A
until the blood type ABO starts
to flash.
3. Use
B
and
C
to scroll through the available
blood type in the following sequence.
A
B
O
AB
Press
C
.
Press
B
.
4. Press
M
to advance to specification of the Rh factor.
•
At this time the current Rh factor (
x
or
*
) will flash on the display.
5. Press
C
to select either
x
(negative) or
*
(positive).
6. Press
A
to store your data and return to the
BLOOD TYPE
screen.
Editing Identification Mode Data (except Blood Type Data)
1. In the Identification Mode, scroll through the data and display the one
you want to edit.
2. Hold down
A
until the cursor appears in the text area.
3. Use
M
to move the cursor to the character you want to change.
4. Use
B
and
C
to change the character.
•
For details on inputting characters, see “Inputting Text and Numbers”
(step 3 for text input and 7 for number).
5. After making the changes that you want, press
A
to store them and
return to the Identification Mode data screen.
Deleting Identification Mode Data (except Blood Type Data)
1. In the Identification Mode, scroll through the data and display the one
you want to delete.
2. Hold down
A
until the cursor appears in the text area.
3. Press
B
and
C
at the same time to clear the data.
•
At this time the cursor appears in the text area, ready for input.
4. Input data or press
A
to return to the Identification Mode data screen.
Blood type ABO
Rh factor
M
A
B
C
P
P
ALARM MODE
You can set the hour and minutes for three
separate Daily Alarms. When the Daily Alarm is
turned on, the alarm sounds for 20 seconds at
the preset time each day. Press any button to
stop the alarm after it starts to sound.
When the Hourly Time Signal is turned on, the
watch beeps every hour on the hour.
•
The mode indicator (
ALM
) indicates an alarm
screen.
SIG
appears in place of
ALM
when
the Hourly Time Signal screen is shown.
Setting an Alarm Time
1. In the Alarm Mode, press
C
to select the
alarm whose time you want to set.
Mode indicator
Hour : Minutes
Alarm No.
Current time
Alarm 1
Hourly Time Signal
Alarm 2
Alarm 3
2. After you select an alarm, hold down
A
until the hour digits of the alarm
time start to flash.
•
This operation automatically turns on the alarm.
3. Press
M
to move the flashing in the sequence shown below to select
other settings.
On/Off
Hour
Minutes
4. While hour or minutes is flashing, press
C
to increase the setting or
B
to decrease it.
•
When the On/Off setting is flashing, press
C
to turn the alarm on
(
ON
) and off (
OFF
).
•
When setting the alarm time using the 12-hour format, take care to
set the time correctly as a.m. (no indicator) or p.m. (P indicator).
5. Press
A
to return to the alarm display screen.
Testing the Alarm
In the Alarm Mode, hold down
C
to sound the alarm.
Turning an Alarm On and Off
1. In the Alarm Mode, press
C
to select the alarm you want to turn on or off.
2. Hold down
A
until the hour digits of the alarm time start to flash.
3. Press
M
twice to select alarm On/Off setting.
•
Alarm On/Off setting is selected when the
ON
or
OFF
setting is
flashing.
4. Press
C
to turn it on (
ON
) and off (
OFF
).
5. Press
A
to return to the alarm display screen.
•
The alarm on indicator (
) is on the alarm display screen when the
alarm is turned on.
•
In other modes (besides the Alarm Mode), the
indicator remains
on the display as long as at least one of the alarms is on.
M
A
B
C
P
Turning the Hourly Time Signal On and Off
1. In the Alarm Mode, press
C
to select the
Hourly Time Signal.
2. Hold down
A
until the
ON
indicator starts
to flash on the display in place of
SIG
.
3. Press
C
to turn it on (
ON
) and off (
OFF
).
4. Press
A
to return to the Hourly Time Signal
display screen.
•
The hourly time signal on indicator (
)
appears on the display whenever the
Hourly Time Signal is turned on.
Hourly time signal
on indicator
M
A
B
C
COUNTDOWN ALARM MODE
The countdown timer can be set within a range
of 1 second to 24 hours. When the countdown
reaches zero, an alarm sounds.
•
You can also select auto-repeat, which
automatically restarts the countdown from the
original value you set whenever zero is
reached.
Setting the Countdown Time
1. In the Countdown Alarm Mode, hold down
A
until the hours digit of the countdown time
starts to flash.
2. Press
M
to move the flashing in the sequence shown below to select
other settings.
Seconds
Hours
Minutes
3. While hours, minutes, or seconds digits are flashing, press
C
to increase
the setting.
•
To set the starting value of the countdown time to 24 hours, set
0:00 00
.
4. Press
A
to return to the countdown alarm display screen.
Mode indicator
1/10 second
Hours : Minutes
Seconds